EUCHNER CTP-AR Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 36

EUCHNER CTP-AR Series Скачать руководство пользователя страница 13

13

2136918-04-05/19 (translation of the original operating instructions)

Operating Instructions

Transponder-Coded Safety Switch CTP-LBI-AP

EN

7.4.

Wire front release

Release via a pull wire. Depending on the type of attachment, the wire front release can be used as emergency unlocking

or escape release.
The following applies to non-latching wire front releases.
If the release is to be used as emergency unlocking, one of the following measures must be

taken (see EN ISO 14119:2013, section 5.7.5.3):

Ì

Install the release so that it can be reset only with the aid of a tool.

Ì

Alternatively, the reset can be undertaken at the control system level. E.g. by means of a

plausibility check (status of the safety outputs does not match the guard locking activation

signal).

The emergency-unlocking specifications in chapter

on

apply irrespective of

this information.

Important!

Ì

The wire front release meets the requirements of Category B accord-

ing to EN ISO 13849-1:2015.

Ì

The correct function depends on the laying of the pull wire and on the

attachment of the pull handle, and this is the responsibility of the plant

manufacturer.

Ì

The actuator must not be under tensile stress during manual release.

7.4.1. Laying wire front release

Important!

Ì

Loss of the release function due to mounting errors, damage or wear.

Ì

Check the release function every time after mounting.

Ì

After manual unlocking, the solenoid must be energized briefly to re-establish the defined state.

Ì

When routing the wire front release, ensure that it operates smoothly.

Ì

Observe the min. bending radius (100 mm) and minimize the number of bends.

Ì

The switch is not allowed to be opened.

Ì

Observe the notes on the enclosed data sheets.

«
...
11
12
13
14
15
...
»

Содержание CTP-AR Series





































Отзывы:

Нет отзывов