EUCHNER 099265 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 38

EUCHNER 099265 Скачать руководство пользователя страница 22

Manual EKS Ethernet TCP/IP

Page 22/38

Subject to technical modifications

2547185-01-10/22

6 Electrical connection

Danger!

Electrical connection may be performed only by

authorized personnel trained in EMC

and with the

device and wiring

isolated

.

Warning!

For use and operation as per the

requirements, a power supply with the feature

“for use in

class 2 circuits”

must be used.

Attention!

The read/write station is allowed to be connected only if it is electrically isolated.

Otherwise the device can be damaged.

Attention!

If connected incorrectly, the device can be damaged.

Observe electrical characteristics and terminal assignment (see chapter 4.4 Technical data for compact

version and chapter 4.5 Technical data for modular version).

Attention!

All the electrical connections must either be isolated from the mains supply by a safety transformer

according to IEC/EN 61558-2-6 with limited output voltage in the event of a fault, or by other equivalent

isolation measures.

Attention!

When connecting, the operating organization must ensure compliance with the EMC protection

requirements in accordance with EN 55011 and EN 61000-6-2.

Attention!

The equipotential bonding system of the machine installation must comply with EN 60204-1, section 8,

Equipotential bonding.

Attention!

Do not lay connecting cables in the immediate vicinity of sources of interference.

«
...
20
21
22
23
24
...
»

Содержание 099265







































Отзывы:

Нет отзывов