manualshive.com logo in svg

EUCHNER 097945, Руководство по эксплуатации, Страница: 23 / 32

Поделиться
Скачать
EUCHNER 097945 Скачать руководство пользователя страница 23

23

2110182-10-02/20 (Translation of the original operating instructions)

Operating Instructions

Non-Contact Safety Switch CES-A-C5H-EX

EN

13.1.1. Technical data, safety switch CES-A-C5H-EX

Parameter

Value

Unit

min.

typ.

max.

Housing material

PBT V0 GF30

Dimensions

Acc. to EN 60947-5-2

mm

Weight

0.4

kg

Ambient temperature at U

B

 = DC 24 V

-20

-

+50

°C

Degree of protection

IP65/IP67

Degree of contamination

3

Rated insulation voltage U

i

-

-

300 

1)

V

Rated impulse withstand voltage U

imp

-

-

1.5

kV

Rated conditional short-circuit current

-

-

100

A

Resilience to vibration

Acc. to EN 60947-5-2

Installation orientation

Any

Connection

M12 plug connector, 8-pin, shield can be connected

Operating voltage DC (regulated, residual ripple < 5 %)

21

24

27

V DC

For the approval acc. to UL the following applies

Operation only with UL class 2 power supply or equivalent measures

Current consumption

80

mA

Switching load acc. to UL

Max. DC 24 V, class 2

External fuse (operating voltage)

0.25

-

8

A

Power supply for load U(+LA)/U(+LB)

18

-

27

V DC

Safety outputs (LA/LB, 2 semiconductor outputs, p-switching, 

short circuit-proof, electrically decoupled)
- Output voltage U(LA/U(LB) 

2)

  HIGH  U(LA)

U(+LA) - 1.5

-

U(+LA)

  HIGH  U(LB)

U(+LB) - 1.5

-

U(+LB)

V DC

  LOW  U(LA)/U(LB)

0

-

1

Switching current per safety output

1

-

100

mA

External fuse (U(+LA)/U(+LB), safety circuit

100 mA medium slow-blow

Utilization category acc. to EN 60947-5-2

DC-13 24 V 100 mA

Monitoring output (OUT, semiconductor output, p-switching, 

short circuit-proof)
- Output voltage

0.8 x U

B

-

U

B

V DC

- Max. load

-

-

20

mA

Risk time 

3)

-

-

180

ms

Discrepancy time

-

-

120

ms

Ready delay 

4)

-

-

3

s

Dwell time 

5)

0.5

-

-

s

Switching frequency

-

-

1

Hz

Repeat accuracy R acc. to EN IEC 60947-5-3

≤

 10

%

Mounting distance between 2 read heads or 2 actuators

80

-

-

mm

EMC protection requirements 

Acc. to EN 60947-5-3

LED displays

STATE 

LED green:  Normal operation

 

Flashing: 

Teach-in operation

OUT/ERROR  LED yellow:  Actuator detected

OUT/ERROR  LED red: 

- EMC interference

 

 

- Internal electronics fault

 

 

- Invalid teach-in operation

Reliability values acc. to EN ISO 13849-1

Category

4

Performance Level (PL)

PL e

PFH

D

3.7 x 10

-9

 / h

Diagnostic coverage DC

99

%

MTTF

D

644

years

Mission time

20

years

1)  Tested by employers’ liability insurance association up to 75 V.

2)  Values at a switching current of 50 mA without taking into account the cable length.

3)  Maximum OFF time for the safety outputs following removal of the actuator.

4)  After the operating voltage is switched on, the semiconductor outputs are switched off and the monitoring outputs are set LOW during the ready delay.

5)   The dwell time of an actuator inside and outside the actuating range must be at least 0.5 s to ensure reliable detection of internal faults in the evaluation unit (self-monitoring).

Содержание 097945

































Отзывы:

Нет отзывов