EUCHNER 097945 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 32

EUCHNER 097945 Скачать руководство пользователя страница 12

Operating Instructions

Non-Contact Safety Switch CES-A-C5H-EX

12

(Translation of the original operating instructions) 2110182-10-02/20

9. Mounting

WARNING

On use in potentially explosive atmospheres the following applies:

Ì

Protection against mechanical effects on the switch:

-Install switch so that the rear of the housing is entirely covered in order to protect it from me-

chanical damage through impact.

CAUTION

Safety switches must not be bypassed (bridging of contacts), turned away, removed or otherwise

rendered ineffective.

Ì

Observe EN ISO 14119:2013, section 7, for information about reducing the possibilities for by-

passing an interlocking device.

NOTICE

Risk of damage to equipment and malfunctions as a result of incorrect installation.

Ì

Safety switches and actuators must not be used as an end stop.

Ì

Observe EN ISO 14119:2013, sections 5.2 and 5.3, for information about mounting the safety

switch and the actuator.

Ì

From the assured release distance S

ar

, the safety outputs are safely shut down.

Ì

When mounting several safety switches, observe the stipulated minimum distance to avoid mutual
interference.

min. 80mm

Ì

If the actuator is installed flush, the operating distances change as a function of the installation
depth and the guard material.

Operating

distance

Actuator

Operating

distance

Actuator

Flush mounting

Surface maounting

«
...
10
11
12
13
14
...
»

Содержание 097945

































Отзывы:

Нет отзывов