eTung MR-900T Скачать руководство пользователя страница 75

Страница: 75 / 76

MR-900T User Manual

Appendix 9: AT Commands on the

Router’s Ethernet Interface

eTung’s wireless routers support AT commands directly coming from Ethernet
interface, to query status, modify parameters, send/receive SMS, etc. The AT

commands that a router supports can be different based on different models and

different firmware versions. Below are the AT commands on the Ethernet interface
that MR-900T V1.4.6 or higher versions support.

Attention: the AT commands MUST be in uppercase, and MUST end with CR (0x0d),
as shown in “\r” below.

For the following commands, please refer the descriptions of AT commands via SMS
in “2.5 Remote Configurations”

AT+WN=apn,user,passwd,net_mode\r

AT+DC=addr,port,user,mode\r

AT+PWD=passwd\r

AT+VIRHUB=0/1\r

AT+RESTORE\r

AT+REBOOT\r

AT+STATUS? \r

AT+WN? \r

AT+DC? \r

10.

AT+INFO? \r

11.

AT+VIRHUB? \r

12.

AT+UPDATE=url\r

13.

AT+UPDATEALL=url\r

Following are the AT commands used to send SMS, for details please refer
“Appendix 7: Send/Receive SMS with the Router’s Ethernet Interface and SMS

Format”.

14.

AT+SMS=<target number>,<encoding format>,<data length>,<data>\r

15.

AT+SMSA=<target number>,<data length>,<data>\r

Following are the AT commands that can be used only on Ethernet interface, and

currently cannot be used via SMS.

16.

AT+UPTIME\r

Get the system’s running time, and the return value is in seconds.

Содержание MR-900T













































































Результаты поиска

Содержание MR-900T

Отзывы:

Бренды по названию

Популярные бренды

eTung MR-900T, Руководство пользователя

Результаты поиска

Содержание MR-900T

Отзывы:

Бренды по названию

Популярные бренды