manualshive.com logo in svg

eTung MR-900T, Руководство пользователя

Поделиться
Скачать
eTung MR-900T Скачать руководство пользователя страница 24

 

 

                                    MR-900T User Manual 

24 

 

 

2.5

 

Remote Configurations 

SMS commands and remote AT commands can be used on MR-900T to 

modify configuration parameters remotely. Details are described 
below: 

 
1.

 

Modify configuration parameters remotely via SMS 

The SMS to configure MR-900T parameters should follow the format 

below: SMS password;AT commands 

 

1)

 

SMS password is the "SMS wakeup password" as shown in 
wireless network settings of the web configuration interface, 

with "1234" by default. This password is used to filter rubbish 

SMS. Long SMS is not supported. 

2)

 

There can be multiple AT commands, and ";" is used between 

SMS and AT command, and between AT commands. If there are 
more than one AT command and some command fails, the 

following commands will not be executed. If a command is 

unknown, an ERROR will return. The commands will take effect 
after system reboot. This can be done by putting a command 

"AT+REBOOT" in the end of SMS commands, or sending a 
separate SMS with command "AT+REBOOT". 

3)

 

AT command must be capitalized, but the parameters in the 

command do not have this limit. 

4)

 

If there are multiple parameters in the command, just write 

those that need to change and you do not have to write all of 
them. If some item does not need to change, write two 

continuous colons, and if some item needs to clean, write a 

space. For example: 

AT+WN=3gnet    (configure onely APN, and other parameters keep 

unchanged) 
AT+DC=,,user      (the first two items keep unchanged, and change 

username only) 

 

 

 

 

 

The contents of SMS must be English characters or digits in single byte, 

and cannot be in double byte

. 

Содержание MR-900T













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды