HI-4413USB Fiber Optic to USB Converter
Quick Start Guide
www.ets-lindgren.com
www.ets-lindgren.com
399310, Rev C
USA Headquarters
1301 Arrow Point Drive
Cedar Park, TX 78613
Phone: +1.512.531.6400
[email protected]
Please see
f
www.ets-lindgren.com
or a list of all ETS-Lindgren offices.
© Copyright 2009–2011 by ETS-Lindgren L.P. All Rights Reserved. No part of this document may be copied
by any means without written permission from ETS-Lindgren L.P.
The
logo,
, and
are trademarks of ETS-Lindgren L.P.;
,
, and
are registered trademarks of Microsoft Corporation
in the United States and/or other countries.
ETS-Lindgren
ProbeView
ProbeView II
Microsoft Windows
Windows Vista
Warranty Information
For warranty information, see the
.
Product Information Bulletin
Safety Information
ONLY QUALIFIED PERSONNEL
should install, operate, or service this equipment.
CONTACT ETS-LINDGREN PRIOR TO SERVICING.
Servicing (or modifying) the unit by yourself
may void your warranty. If you attempt to service the unit by yourself, disconnect all electrical power
before starting. There are voltages at many points in the instrument that could, if contacted, cause
personal injury. Only trained service personnel should perform adjustments and/or service procedures
upon this instrument. Capacitors inside this instrument may still be CHARGED even when instrument is
disconnected from its power source.
WARRANTY
For complete safety information, see the
.
Product Information Bulletin
Maintenance of Fiber Optics
Fiber optic connectors and cables can be damaged from airborne particles, humidity and moisture,
oils from the human body, and debris from the connectors they plug into. Always handle connectors
and cables with care, using the following guidelines. Failure to perform these tasks
may result in damage to the fiber optic connectors or cables.
Before performing any maintenance, disconnect the fiber optic cables from the unit
and turn off power.
•
When disconnecting fiber optic cables, apply the included dust caps to the ends
to maintain their integrity.
•
Before connecting fiber optic cables, clean the connector tips and in-line connectors.
•
Before attaching in-line connectors, clean them with moisture-free compressed air.
•
Failure to perform these tasks may result in damage to the fiber optic connectors or cables.
The
battery-powered probes to communicate
with ProbeView II™ or ProbeView™ LT software
through a USB port on a computer.
ETS-Lindgren HI-4413USB Fiber Optic to USB Converter
enables
The following ETS-Lindgren probes
may be used with the HI-4413USB;
up to one probe at a time may be
connected to the HI-4413USB.
HI-6005
Electric Field Probe
HI-3638
ELF / VLF Electric Field Meter
HI-6022
Electric Field Probe
HI-3702
Clamp On Induced Current Meter
HI-6053
Electric Field Probe
HI-44
Series
Broadband Isotropic Field Probe
XX
Required Components
HI-4413USB Fiber Optic to USB Converter with standard
USB A-type male to USB mini-B male cable
•
Fiber optic cable, part # 491106-
, where
=length in meters (not included)
nn
nn
•
ProbeView II or ProbeView LT (not included)
•
Personal computer with Microsoft® Windows® operating system
(see next page for list of supported operating systems) and
one available USB port (not included)
•
USB driver (not included)
•
ETS-Lindgren battery-operated probe (not included)
•
Note:
ETS-Lindgren may substitute a similar part or new part number with the same functionality
for another part/part number. Contact ETS-Lindgren for questions about part numbers and
ordering parts.
Revision/Date:
B, Update driver info - March, 2011
A, Initial Release - October, 2009
C, Update driver steps - October, 2011
