ETIC 1220 Скачать руководство пользователя страница 15

Страница: 15 / 64

INSTALLATION

XSLAN SHDSL switch

User’s guide ref 9014709-02

Page 15

1.3

DIP switches and push-button

DIP switches

SW 1 SW 2

Management

OFF

The current IP@ of the product is the stored IP @

OFF

The active IP@ of the product is the factory IP@ : 192.168.0.128
No login and password are required to access to the html server

OFF

The active IP@ is provided by the BOOTP or DHCP server

No IP @ is assigned to the product; DIP switch configuration

SW 3 SW 4

SW 5

Shdsl port 1

OFF

NTU mode

OFF

LTU mode - Auto

OFF

LTU mode – 2304 kbit/s

OFF

LTU Mode – 2048 kbit/s

OFF

LTU Mode – 1536 kbit/s

OFF

LTU Mode – 1024 kbit/s

OFF

LTU Mode – 512 kbit/s

LTU Mode – 256 kbit/s

SW 6 to SW 12

Not used - Must be left OFF

Push-button :

A push-button is located close to the DIP switches.
It enables to restore the factory profile.
To restore the factory profile, switch the power on while pressing the
push-button until the OPERATION led turns green.

Attention

: Once the factory profile has been restored, the stored

configuration is lost.

Содержание 1220

































































Результаты поиска

Содержание 1220

Отзывы:

ETIC 1220, Руководство пользователя, Страница: 15 / 64

Результаты поиска

Содержание 1220

Отзывы: