Industrial Web-Smart High Power PoE Ethernet Switch
This quick start guide describes how to install and use the Industrial Web-Smart High Power PoE (Power
over Ethernet) Ethernet Switch. This is the switch of choice for harsh environments constrained by space.
Physical Description
The Port Status LEDs and Power Inputs
LED State
Indication
Steady Power
on.
Power1
Power2
Power3
Off Power
off.
Steady
Power redundant system failure
occurred.
Fault
Off
Power redundant system failure is
not occurred.
10/100Base-TX, 100Base-FX/BX
Steady
A valid network connection
established.
Link/ACT
Flashing
Transmitting or receiving data.
ACT stands for ACTIVITY.
Steady
Valid port connection at 100Mbps.
10/100
Off
Valid port connection at 10Mbps.
Steady
Powered Device (PD) is connected.
PoE
Off
Powered Device (PD) is
disconnected.
Power Input Assignment
Power3 55VDC
DC
Jack
＋
55VDC
Power2
－
Power Ground
＋
55VDC
Power1
－
Power Ground
Earth Ground
Terminal Block
Relay Output Rating
1A @ 24VDC
Relay Alarm Assignment
FAULT
*Relay warning signal disable for following:
1. The relay contact closes if Power1 and
Power2 are both failed but Power3 on.
2. The relay contact closes if Power3 is failed
but Power1 and Power2 are both on.
The 10/100Base-TX and 100Base-FX/BX Connectors
The 10/100Base-TX Connections
The following lists the pinouts of 10/100Base-TX ports.
Pin PoE Ports (Port 1-4)
Non-PoE Port (Port 5)
1
Output Transmit Data + Output Transmit Data +
2
Output Transmit Data - Output Transmit Data -
3
Input Receive Data +
Input Receive Data +
4 Positive
(VCC+)
5 Positive
(VCC+)
6
Input Receive Data -
Input Receive Data -
7 Negative
(VCC-)
8 Negative
(VCC-)
The 100Base-FX Connections
The fiber port pinouts
The Tx (transmit) port of device I is connected to the Rx (receive) port of device II,
and the Rx (receive) port of device I to the Tx (transmit) port of device II.
The WDM 100Base-BX Connections
The fiber port pinouts
Only one optical fiber is required to transmit and receive data.
Functional Description
•
Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial environment.
•
Manageable via Web browser interface.
•
Port 1 – 4 support Power over Ethernet (PoE) Power Sourcing Equipment (PSE).
•
High Power PoE design up to 30W.
•
Supports 802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps, full/half-duplex. Auto MDI/MDIX.
•
100Base-FX: Multi mode/Single mode SC or ST type. 100Base-BX: WDM Multi mode/Single mode
SC type.
•
Supports 1024 MAC addresses. Provides 512K bits memory buffer.
•
Alarms for power and port link failure by relay output.
•
Power Supply: Redundant 55VDC Terminal Block power inputs and 55VDC DC JACK with optional
100-240VAC external power supply.
•
Operating voltage and Max. current consumption: 2.36A @ 55VDC. Power consumption: 130W
Max.
•
-10
to
℃
60
(
℃
-14
℉
to 140
℉
) operating temperature range. Tested for functional operation @
-20
to
℃
70
(
℃
-4
℉
to 158
℉
).
•
Supports Wall and Desktop Mounting installation.
1 V2
