EtherWAN EX24000 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 239

EtherWAN EX24000 Скачать руководство пользователя страница 85

TRUNKING

Overview

Port Trunking refers to the use of multiple network connections in parallel to increase the link
speed beyond the limits of any one single cable or port. This is commonly called link
aggregation. These aggregated links may be used to interconnect switches or to connect
high-capacity servers to a network.

The EtherWAN EX24000 Switch supports up to six trunks for 100Mbps ports and up to two
gigabit trunks. Each 100Mbps trunk can be composed of up to eight 100Mbps ports while
each gigabit trunk can support up to four gigabit ports.

There are two popular types of port trunking, static and link aggregation control

protocol (LACP). We will take a minute to discuss both types of trunking and why one would
want to use them.

Static Channel Trunking

Originally specified in the IEEE802.3AD specification and now in the IEEE

802.1AX2008 specification, this type of trunking is the most basic and easiest to understand.
It simply is the aggregation of two or more Ethernet links to form a virtual link equivalent in
bandwidth to the sum of its individual links. For example, if one had four 100Mbps Ethernet
links composing a single static channel, the overall bandwidth of the static channel would be
400Mbps.

Prioritization of data through the channel is simple as well. When one of the links of

the channel becomes saturated the excess data spills over into the remaining channels. For
example, if one were sending a constant stream of data at 250Mbps through a static channel
composed of 4 individual 100Mbps links, the first two links of the channel would be
completely saturated while the half of the third channel would be utilized and none of the
forth channel would be used.

Link Aggregation Control Protocol

Within the IEEE specification, the Link Aggregation Control Protocol (LACP) provides

a method to control the bundling of several physical ports together to form a single logical
channel. LACP allows a network device to negotiate an automatic bundling of links by
sending LACP packets to the peer (directly connected device that also implements LACP).
This means that both sides of the LACP channel must be configured for LACP which implies
both devices must support it.

85

EX24000 Switch Users Guide

«
...
83
84
85
86
87
...
»

Содержание EX24000
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды