EtherWAN EX24000 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 239

EtherWAN EX24000 Скачать руководство пользователя страница 33

Management Interface

To navigate to the

Management Interface

page:

1. Click on the

+

next to

System

2. Click on

Management Interface

The Management Interface configuration page has three settings that allow the user to
configure the methods available to manage the EX24000 Switch.

HTTPS

HTTPS (Hypertext Transfer Protocol Secure) allows the user to determine what
method, if any, is used to configure the EX24000 Switch. The default is unencrypted
HTTP (see

To disable the Web interface:

1. Uncheck

Http

and

Https.

2. Click on the

Update setting

button.

Warning! Once the Submit button is pressed, the Web console will no longer

function. As a safety precaution, the configuration is not saved by default. Rebooting
the EX24000 Switch will restore the Web Console. To save the configuration,
connect using the new IP address.

To enable the Web Interface:

1. Check

HTTP

,

HTTPS

or both

2. Click on the

Update Setting

button.

3. Save the Configuration (see

Save Configuration

Telnet

.

Telnet is a network protocol that allows a remote computer to log into the EX24000
Switch to access its CLI (Command Line Interface). The CLI can be access using
Telnet, SSH and the serial port on the EX24000 Switch. The secure method of
accessing the CLI over a network is SSH.

To enable or disable Telnet:

1. Click the

Enable

or

Disable

radio button in the Telnet section on the

Management Interface page (see

below)

33

EX24000 Switch Users Guide

«
...
31
32
33
34
35
...
»

Содержание EX24000
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды