EtherWAN EX24000 Скачать руководство пользователя страница 28

Страница: 28 / 239

SYSTEM MENU

System Information

The System information link on the Left menu of the Web Configuration page takes you to a
page that shows the following (see

Figure 6



System Name

The System name is typically used by network administrators. If SNMP is

enabled on the switch, the system name can be found using MIB II (RFC1213)
in the sysName property.



Firmware Version

If SNMP is enabled on the switch, the Firmware version can be found using

MIB II in the sysDesc property



System Time

System time can be change using NTP



MAC Address

The hardware (MAC) address of the Management interface



Default Gateway

The IP address of your networks Gateway (Typically a Router on your

network)



DNS Server

The Dynamic Name Server (DNS) for your network



VLAN ID

One or more listings depending on the number o VLANs defined on the

switch

Lists VLAN ID, IP address, and subnet mask of the VLAN Interface(s)



Current User Information

EX24000 Switch Users Guide

Содержание EX24000
















































































































































































































































Результаты поиска

Содержание EX24000

Отзывы:

Похожие инструкции для EX24000

Бренды по названию

Популярные бренды

EtherWAN EX24000, Руководство пользователя

Результаты поиска

Содержание EX24000

Отзывы:

Похожие инструкции для EX24000

Бренды по названию

Популярные бренды