manualshive.com logo in svg

EtherWAN EX24000, Руководство пользователя

Поделиться
Скачать
EtherWAN EX24000 Скачать руководство пользователя страница 234

 

DHCP Server 

DHCP is a TCP/IP application protocol that allows any TCP/IP device to dynamically obtain 
its initial TCP/IP configurations through the TCP/IP protocol itself (in this case, through the 
UDP protocol). It is based on the client-server paradigm. The EtherWAN switch can be setup 
as a DHCP server to allow any DHCP client to dynamically obtain its IP address, default 
router, and DNS servers. 

 

General Overview  

The EtherWAN switch can function as a DHCP server for a single VLAN (it can be any 
VLAN) on the switch. When functioning as a DHCP server, the EtherWAN switch can be 
configured with a range of IP addresses, default gateway and DNS servers, which will allow 
the switch to use the dynamic configuration function of the DHCP protocol to provide any 
TCP/IP device that is a DHCP client, to dynamically obtain an IP address, default router, and 
DNS servers. The EtherWAN DHCP server can also be configured with a lease period that 
the DHCP clients are allowed the use of their assigned IP address. In this simple 
implementation, both the DHCP Client and the DHCP Server must be on the same network 
(same VLAN). 

Configuring the DHCP Server 

To navigate to the 

DHCP Server

 page: 

1.  Click on the 

+

 next to 

Other Protocols

 

2. Click on 

DHCP Server

 (see 

Figure 112

) 

 
You can use the GUI to set the following DHCP server parameters: 

 

 DHCP 

Server 

Enable 

 DHCP 

VLAN. 

 DHCP 

Client 

Parameters 

o

  IP Address range 

o

 Subnet 

Mask 

o

 Default 

gateway 

o

  Primary and Secondary DNS. 

  DHCP Client lease time 

 

 
 
 
 
 

234 

EX24000 Switch Users Guide 

Содержание EX24000
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды