6
A S S E m B ly A n D o P E r A t i n g i n S t r u C t i o n S | e n E X H o - P r - P r E S E n C E D E t E C t o r
When installing a eNEXHO-PR presence detector, try to avoid
installing the device in areas subjected to the following (or si-
milar) conditions:
› Locations where the device could be exposed to impacts or
vibrations.
›
Locations with elements which could obstruct the field of
view of the sensor (for example, glass).
› Locations where the device is exposed to direct sunlight.
› Locations where the device is exposed to wind or to draughts
coming from a heating or air conditioning element.
› Environments subject to rapid changes in the atmosphere.
The detection range is depicted in the following diagram:
Remove the front casing by pressing the lateral release but-
tons. Place the AAA batteries in the compartment as indicated
by the polarity markings.
In order to mount the detector in a corner, place the corner
mounting bracket provided with the equipment in the desired
location. Use a pencil to mark the location of the fixing screw
holes.
Remove the bracket momentarily and insert the wall plugs in
the marked locations. Partially insert the screws into the wall
plugs using a screwdriver and place the bracket into the cor-
ner again. Insert the screws into the holes previously used as a
marker. Drive the screws fully into the bracket until it is firmly
fixed. Insert the bracket bolts in the pre-die cut holes that you
will find at the back of the eNEXHO-PR sensor.
Please note that the presence detector must be con-
figured together with the eNEXHO-NT internet con
-
trol module so that the detector is installed in the system
and can be controlled from one of these control units. For
that purpose, consult the section on how to install presence
detectors in your automation network in the user manual of
the eNEXHO-NT internet module.
Once the device has been configured in the home-auto
-
mation system, it is advisable to install an audible warning
alarm for interior spaces connected to a eNEXHO-CR pow-
er-control module. Please consult the user manual of the
eNEXHO-NT internet module to learn how to configure the
security mode so that it activates the audible warning alarm
in case of detection.
W H E r E S H o u l D i i n S t A l l A e n E X H o - P r P r E S E n C E S E n S o r ?
i n S t A l l A t i o n r u n n i n g o n B A t t E r i E S
Remove the frontal housing by pressing the lateral release but-
tons.
In order to mount the detector in a corner, place the corner
mounting bracket provided with the equipment in the desired
location. Use a pencil to mark the location of the fixing screw
holes.
Remove the bracket momentarily and insert the wall plugs in
the marked locations. Partially insert the screws into the wall
plugs using a screwdriver and place the bracket into the cor-
ner again. Insert the screws into the holes previously used as a
marker. Drive the screws fully into the bracket until it is firmly
fixed. Insert the bracket bolts in the pre-die cut holes that you
will find at the back of the eNEXHO-PR sensor.
Guide the cables from the external power supply through the
hole of the device designed for this purpose and place the bolts
of the corner bracket in the pre-die cut holes at the rear part
of the detector. Plug the power cables into the corresponding
terminals as indicated in the following image:
Please note that the presence detector must be con-
figured together with the eNEXHO-NT internet con
-
trol module so that the detector is installed in the system
and can be controlled from one of these control units. For
that purpose, consult the section on how to install presence
detectors in your automation network in the user manual of
the eNEXHO-NT internet module.
i n S t A l l A t i o n r u n n i n g o n E X t E r n A l P o W E r S u P P ly
