manualshive.com logo in svg

ETC Unison ERn2-W, Руководство по установке

Поделиться
Скачать
ETC Unison ERn2-W Скачать руководство пользователя страница 39

Install Rack Options

35

Status Indicators

When power is applied to the ERn enclosure, the Paradigm Ethernet Switch Module LEDs, located on 
the front panel, indicate main power, data, and PoE power status.

• The power LED is blue and will illuminate when the Ethernet Switch is powered.
• The LINK/ACT and PoE power LEDs are typical of an Ethernet Switch.
• The Link/Act indicator is green and is on if there is a device connected to that port. A blinking LED 

indicates data activity on the port.

• The PoE indicator is yellow and will be on if the Ethernet Switch is supplying power to the device 

connected to that port. A blinking PoE LED indicates a powering error on that port.

Note:

Port one does not have a port power indicator as it does not supply power. Port one 

is always connected to the Paradigm Architectural Control Processor which is 

powered by the ERn enclosure power supply.

PoE

Power

LINK/ACT

1

2

3

4

5

Содержание Unison ERn2-W









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды