manualshive.com logo in svg

ETC Unison ERn2-W, Руководство по установке

Поделиться
Скачать
ETC Unison ERn2-W Скачать руководство пользователя страница 36

32

ERn Wall-mount Installation Manual

Status Indicator

When the Redundant Power Supply is installed properly, and power is applied to the ERn enclosure, the 
LED will indicate in green if the supply is powered. If the LED is off but the primary rack supply status 
indicator is on, the Redundant Power Supply requires servicing. Alternatively, if the primary rack supply 
status LED is off, but the Redundant Power Supply is on, the primary rack supply requires service. 
Contact ETC Technical Services for assistance. See 

Contacting ETC

 on 

page 5

.

Install the Ethernet Switch Module

The ERn Ethernet Switch Module installs in the bottom option module tray of the ERn enclosure, 
replacing the blank module that ships with the rack from the factory. The bottom option slot is the only 
position for the Ethernet Switch Module.

An ERn Ethernet Switch (ERn-NET) provides five ports of Power over Ethernet (PoE). The kit includes , a 
Switch module patch panel, Ethernet Switch panel, and five patch cables. 

Note:

The ERn Ethernet Switch module (ERn-NET) is not supported in an ERn4 enclosure at 

230 VAC, nor is it compatible with a rack mounted ERn enclosure.

Note:

The ERn-NET option is intended for use only in wall mount ERn enclosures and is not 

compatible with rack mounted enclosures.

Switch 
module

patch panel

Ethernet Switch 
panel

Содержание Unison ERn2-W









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды