ETC S4LEDS3D Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 36

ETC S4LEDS3D Скачать руководство пользователя страница 34

30

Source Four LED Series 3 User Manual

RDM Parameters

Parameter

Fixture

Value

Description

Manufacturer ID

All

0x6574

Electronic Theatre Controls

Model ID

S4LEDS3L, S4LEDS3LS

0x0500

ETC Source Four LED Series 3 Lustr

S4LEDS3D, S4LEDS3DS

0x0501

ETC Source Four LED Series 3 Daylight

DMX Personality

All

0x00E0

1 = Direct

2 = Expanded

3 = Studio

4 = RGB

5 = 1-channel

DMX Start Address

All

0x00F0

Range = 1–512

Fixture Compliance

For current and complete compliance and specifications, see the Source Four LED Series 3
datasheet at

.

FCC Compliance

Source Four LED Series 3

(For any FCC matters):

Electronic Theatre Controls, Inc.
3031 Pleasant View Road
Middleton, WI 53562
+1 (608) 831-4116

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received; including interference that may cause undesired operation. Visit

etcconnect.com/products

for current and complete compliance information including FCC

compliance.

This device contains a wireless module with the following identification numbers:

FCC ID: VU65995

«
...
32
33
34
35
36
»

Содержание S4LEDS3D





































Отзывы:

Нет отзывов