ETC GDS BluesSystem Скачать руководство пользователя | Manualshive

Страница: 9 / 28

background image

System Overview

6

Power Supplies

Overview

The BluesSystem Power Supply provides power for the BlueDome and BlueBeam low-voltage
LED lights. Power supplies are available in a One-Zone and Six-Zone variants.

The One-Zone LV Power Supply provides power for up to 10 BlueBeam and BlueDome
running lights and is wall mounted. The wall mounted One-Zone LV Power Supply is available
in two models either DMX512 or Switched Control, depending on control requirements.

The Six-Zone LV Power Supply provides power for up to 10 BlueBeam and BlueDome running
lights per zone. Six-Zone power supplies are available in both rack mount and wall mount
variants, and offer three control options, DMX512, Switched Control, or 0-10 VDC Control.

«
...
7
8
9
10
11
...
»

Содержание GDS BluesSystem





























Отзывы:

Нет отзывов

Похожие инструкции для GDS BluesSystem

Бренд: Rangevision Страницы: 31

Бренд: Bard Страницы: 36

Бренд: Bard Страницы: 2

Бренд: Bard Страницы: 30

Бренд: Bard Peripheral Vascular Страницы: 44

Бренд: dbx Страницы: 2

Бренд: xsto Страницы: 76

Бренд: F&V Страницы: 5

Бренд: F Care Systems Страницы: 2

Бренд: Rainin Instrument Страницы: 16

Бренд: Gardol Страницы: 80

Бренд: Sammode Страницы: 12

Бренд: Sanela Страницы: 5

Бренд: Eurosystems Страницы: 39

FOT-930 MaxTester

Бренд: EXFO Страницы: 8

Бренд: GLP Страницы: 28

Бренд: TLW Страницы: 2

Бренд: IntesisBox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды