ETC echoflex MOS-MT Series Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 8

ETC echoflex MOS-MT Series Скачать руководство пользователя страница 1

MOS-MT

MOS-MT wireless ceiling mount IoT sensor

Installation Guide

Overview

This guide covers the MOS-MT IoT Ceiling Sensor.

1. MOS-MT-

x

A Motion, photo, temperature and audio sensor with small

motion short range lens (1000 sq. ft.)

2. MOS-MT-

x

B Motion, photo, temperature and audio sensor with large

motion large range lens (1900 sq. ft.)

Where x is the frequency of the unit: U=902 MHz or Y=868 MHz.
The package includes the occupancy sensor, lens mask sticker, mounting

plate with integrated magnets for T-Bar ceiling, wire straps and installation

guide. A programming guide with detailed information on implementation is

available for download on www.echoflexsolutions.com.

Sensor Description

The MOS-MT IoT ceiling sensor is a self-powered wireless sensor offering

occupant detection, light level, temperature and sound level monitoring for

the collection of and sharing of data for Internet of Things. Facility operations

use the IoT sensor data via gateways or interfaces to track occupancy levels

and environment mapping for building-use optimization. Areas not being

used can be placed into set-back mode to conserve energy. The detector is

optimized for ceiling heights of 8 - 10 feet (2.4 - 3 meters).
These sensors are intended for indoor use only.

Note:

The MOS is a solar powered device that absorbs solar energy

storing it for use during low light periods. Before assigning

the MOS device to a receiver/controller, the device should be

exposed to a good light source for a minimum of 5 minutes

or install the start assist battery.

i

1
2
3
...
»

Содержание echoflex MOS-MT Series









Отзывы:

Нет отзывов