manualshive.com logo in svg

ETAS ETK-V1.1, Руководство пользователя

Поделиться
Скачать
ETAS ETK-V1.1 Скачать руководство пользователя страница 14

ETK-V1.1 - User’s Guide

14

ETAS

Introduction

3

Introduction 

This section contains information about the basic features and applications of 
the ETK-V1.1 (ETK = Emulator Test Probe), hints to system requirements, and 
other details.

3.1

Applications

The ETK-V1.1 is an emulator probe especially for the Freescale MPC55xx/ 
MPC56xx microcontroller family, e.g. MPC5534, MPC5553, MPC5554 and 
MPC5674F as well as the ST SPC56x family. It is a typical parallel ETK with a 16 
bit interface based on the modular Vertical interface concept from Freescale and 
ETAS. 

Fig. 3-1

ETK-V1.1 (left: ETK-V1.1A, right: ETK-V1.1B)

It is compatible with the ETAS calibration and development system interface (e.g. 
ES590, ES591, ES592, ES595, ES910 and ES1000.2/ES1000.3 with ES1232-A). 
Earlier systems (e.g. MAC2, ES1000.1 with ES1201 board) are not supported. 

3.2

Features 

• Applicable for an external Freescale 16-bit microcontroller bus
• Supports 16- and 8-bit access to the data emulation memory
• CPU bus interface voltage 2.5 V/ 3.3 V/ auto sense option
• Two pages of data emulation/measurement data memory available, each 

with 1 MByte

• Permanent storage of emulation data in flash memory
• RAM adaptor mode
• Can drive "Boot configuration" to configure the CPU
• ECU flashing via ETK 
• Configurable ETK chip select 
• Enable or disable the ETK by ECU software 
• Braindead flashing under ProF control 

Note

The ETK-V1.1 can be shipped in two different mechanical versions (refer to 
chapter 7.12 on page 47 and to chapter 9.1 on page 56).

Содержание ETK-V1.1
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды