manualshive.com logo in svg

ETAS ES593.1-D, Руководство пользователя, Страница: 30 / 71

Поделиться
Скачать
ETAS ES593.1-D Скачать руководство пользователя страница 30

ETAS

Getting Started

ES593.1-D

 

-

 

User Guide

30

6.3.1

“HOST” Port 

To connect the ES593.1-D module with the PC (“HOST” port), you require the 
CBE100 cable provided. 

To connect the ES593.1-D with the PC

1. Connect the 

HOST 

port of the ES593.1-D with the PC interface 

cable CBE100.

2. Connect the cable’s RJ-45 connector with the free Ethernet 

interface of your PC.

6.3.2

“7-29V” Port

To connect the ES593.1-D module with the power supply, you require the 
CBP120 cable or the CBP1205 cable provided.

To connect the ES593.1-D with the power supply

1. Connect the cable CBP120 or the cable CBP1205 for the power 

supply with the 

7-29V 

port of the ES593.1-D. 

2. Connect the supply voltage pins of the cable with the required 

power supply. 
Note the color coding of the connectors.
Note the current consumption of the ES593.1-D and its supply 
voltage range. The admissible values are listed in section 
8.10.1 on

 

page

 

47. 

6.3.3

“ETH1” and “ETH2” Port

To connect the ES593.1-D module with other modules (“ETH1” and “ETH2” 
port), you require the CBE130 cable. 

Simple Module Network

A simple module network consists of a single ES593.1-D module with con

-

nected network or measure modules. ES59x measure modules are used in the 
following example.

NOTE

Make sure you carefully check the names of the cables used. Using the wrong 
cables can keep your ES593.1-D from functioning properly or damage 
theES593.1-D and any devices connected to it. 

DANGER

Dangerous electrical voltage!

Connect the power cable only with a suitable vehicle battery or with a suitable 

lab power supply! The connection to power outlets is not allowed!
To prevent an inadvertent insertion in power outlets, ETAS recommends to 

equip the power cables with safety banana plugs CBP1205 in areas with 

power outlets.

Содержание ES593.1-D








































































Отзывы:

Нет отзывов