ETAS CBS100.1-2 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 39

background image

ETAS

General

CBS10x.1-2 - User’s Guide

8

Fastening with cable ties

Opening the electronic module

Lambda sensor

The lambda sensor connected to the product requires a power supply for the
sensor heater.

Safety notices for specific components

CAUTION

Damage to the housing is possible!

Cable ties for fastening the Smart Lambda Sensor Cable may be attached

only to the infeed lines of the cable. Fastening on the electronic module

(housing) of the cable is not allowed.

CAUTION

Loss of the function is possible!

Do not open the electronic module (housing) of the Smart Lambda Sensor

Cable! A safe function in the re-closed state cannot be guaranteed.

NOTICE

Each lambda sensor is individually trimmed via a resistor in the plug of the

lambda sensor. For this reason, the plug of the lambda sensor may not be

removed.

CAUTION

If the sensor heater is missing, it could lead to premature deterioration or

damage of the lambda sensor.

The lambda sensor must be supplied with current at all times as soon as it is

exposed to the exhaust gases of a combustion process.
If the CBS10x.1-2 cable is connected with a voltage supply, the required reg

-

ulated sensor heater voltage is provided at the sensor connection.

CAUTION

Risk of burns!

The LSU4.9 lambda sensor connected to the lambda sensor cable will

become very hot during operation.

«
...
6
7
8
9
10
...
»

Содержание CBS100.1-2








































Отзывы:

Нет отзывов

Похожие инструкции для CBS100.1-2

Бренд: I-G3N Страницы: 28

Бренд: Gates Underwater Products Страницы: 49

Бренд: Gates Underwater Products Страницы: 45

Бренд: Nautronic Страницы: 7

Бренд: NAPCO Страницы: 16

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 155

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 44

Бренд: Metra Electronics Страницы: 12

Бренд: Halfords Страницы: 4

Бренд: Alpine Страницы: 69

Бренд: Allen Sports Страницы: 2

Бренд: R&G Страницы: 4

Isolette 8000 plus

Бренд: Dräger Страницы: 30

Бренд: EINHELL Страницы: 130

Бренд: Quadratec Страницы: 8

Бренд: Ecco Страницы: 24

Coca-Cola Americana 10LG

Бренд: Cooluli Страницы: 8

mountlogic Series

Бренд: B-Tech Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды