manualshive.com logo in svg

eta EEP 130, Руководство по эксплуатации

Поделиться
Скачать
eta EEP 130 Скачать руководство пользователя страница 18

18

www.eta.co.at

Configuration

6

Configuration

Content of this configuration

Only the steps required for the configuration of this
product are described below. The configuration of the
complete heating system is described in the "Configu-
ration" manual supplied with the boiler.

Software version X.33.0 or later

The configuration requires software version X.33.0 or
later on the boiler.

An update must be performed first if an older version is
installed.

Starting the configuration assistant

The process of starting the configuration assistant
differs depending on the installed software version.

Software version X.35.X and earlier

•

Increase the authorisation to [Service]. Then open
the [Toolbox] menu by pressing the 

 button and

the [Configure system] button.

Software version X.36.0 and later

•

In the system settings 

, increase the authoriza-

tion to [Service] and open the system configuration
menu with the [Systems configuration] button.
Start the configuration assistant with the 
[Starting the assistant] button.

Description for software version X.36.0 and later

The following description and screen shots represent
the software interface of version X.36.0 and later.

Function block [Precip.] is already installed

The function block [Precip.] for controlling the precipi-
tator has already been installed at the factory. For
monitoring purposes, check whether this is shown in
the [Selected function blocks] column in the function
blocks overview.

If you have accidentally deleted the function
block and wish to reinsert it, contact ETA

Customer Service. As some parameters have to be
reset.

Adjusting options in the function block [Boiler]

To start up the precipitator, the option [Electro-
static precipitator] in the function block of the

boiler must be activated.

Select the required function block from the [Selected
function blocks] column:

Open the option and enable the following:

Press the [Accept] button to save.

Establishing a [Flue gas] connection

Establish a new connection by pressing the button
[New connection] and select the connection type [Flue
gas] The producers and consumers must be specified
for these; see the following table.

Further configuration and installation

Continue with configuration and installation of the
heating system as described in the "Configura-

tion" manual supplied with the boiler.

Selected function blocks

HA-C 0

Boiler

Electrostatic precipitator

Connections

Flue gas

Producers

HA-C 0: Boiler: Flue gas

Consumers

EM-C 8: Precip.: Flue gas

Содержание EEP 130

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды