background image

2     

 

The Estate Swing is only to be used for vehicular swing gates in a Class I  

setting. 

 

Class I: A vehicular gate opener (or system) intended for use in a home of one-to-
four single family dwelling, or a garage or parking area associated therewith. 

The Estate Swing automated system was designed and built for controlling vehicle access. 
Do not use for any other purpose. 
 

Max gate leaf size: 

 
 
 
 

IMPORTANT INFO ABOUT GATE 

 

The gate and post must be suitable for being automated. Check that the structure is 
sufficiently strong and rigid, and its dimensions and weights conform to those indicat-
ed above. 

 

Make sure the gates move smoothly without any irregular friction during entire travel. 

 

Make sure the hinges are in good condition. Ball bearing hinges are necessary for 
automation. 

 

Make sure the gate is plumb and level. 

 

The gate post must be secured in the ground with concrete. This will prevent altera-
tion of alignments and leveling during installation and during cycles. 

 

Gate must not have more than 50% coverage preventing wind from passing  through 
gate. 

 
The system displayed below is a recommended standard system. Other approved accesso-
ries can be installed. Photo sensors and a flashing light indicating gate movement is rec-
ommended for safety purposes. 
 

1,2 

Estate Swing Operator • 

3

 Photocells (not included) • 

4

 Control box 

6

 Keypad (not 

included) • 

7

 Receiver extension (not included)• 

8

 12Vdc flashing lamp (not included) • 

9

 

Positive stop (not included) • 

10 

Charging Control 

16’ 

16’ 

16’ 

650lbs 

650lbs  650lbs 

Notes: 

1) When laying electrical cables, use appropriate rigid and/or flexible tube 
2) Do not run any wires in the same conduit as110 AC power that may be in the area. This will 
cause danger of electrocution. 

Important: Do not turn the shaft of the operator arm until the post and gate  

brackets are fully installed. 

Emergency Release 

Emergency Release Procedure:

 

1) Remove the pin as seen to the right. 
2) Swing motor off of the gate bracket. 
3) Swing gate and opener out of the way of 
access. 

Important Notes About Product 

 

The gate opener is device of convenience for opening and closing the gate, not a securi-
ty device. Estate Swing is not responsible for the security of property on  which the 
gate opener is installed. Additional accessories such as gate locks, videocoms, and oth-
er devices are available to enhance security, are sold separately, and may or may not be 
available under the Estate Swing brand.  

 

This product is a Do-It-Yourself product. It is intended to be installed, repaired and 
maintained by a purchasing home owner. Any and all paid labor involved with this 
product is the sole responsibility of the individual that hired the labor. 

 

Properties that contain live stock, children and pets should not allow them direct access 
to the gate safety zone. Additionally we suggest the following precautions: Install safe-
ty edges and photo eyes, do not use any devices that open the gate automatically for 
vehicles such as loops or exit sensors, install an automatic gate lock and positive stops, 
do not use auto-reclose or remote access devices - only trigger the gate to move while it 
is in direct site. 

Содержание E-S Allegiant Series
















Отзывы: