Essilor Instruments DELTA Скачать руководство пользователя страница 11

Страница: 11 / 187

a. Turn on the product

Press on the main switch located on the top of the product to power it up.

The tracer-centerer-blocker part is initialized.

A beep indicates that the initialization was successful.

Then, the edger part is initialised.

A beep indicates that the initialization was successful.

On the screen, press on the

icon to finish the initialisation phase.

A beep indicates that the initialization was successful.

The initial work screen is displayed.

b. Turn off the product

Before switching off the edger:

•

Check that there is no lens in the trough

•

Check that the lens clamp shafts are loosened and that the trough door is open

•

Go to the work screen.

Press on

, then on

A confirmation message is displayed on each screen.

Press

to confirm.

The product shuts down.

Extended period of non-use

For a prolonged period of non-use (a few days), it is preferable to power down the product using the

main switch.

c. Using the touch screen and keypads

Using the touch screen

It is possible to navigate between the tracer-centerer-blocker screen and the edger screen in 2 different

ways:

Delta - Edging System > V1- 02-2020

SER

ANUAL

> II. F

IRST

TEPS

WITH

ELTA

Содержание DELTA




























































































































































































Результаты поиска

Содержание DELTA

Отзывы:

Essilor Instruments DELTA, Руководство пользователя, Страница: 11 / 187

Результаты поиска

Содержание DELTA

Отзывы: