background image

ESP32-Ethernet-Kit V1.0 Getting Started Guide

This guide shows how to get started with the ESP32-Ethernet-Kit development board and also 

provides informa on about its func onality and configura on op ons.

The 

ESP32-Ethernet-Kit

  is  an  Ethernet-to-Wi-Fi  development  board  that  enables  Ethernet 

devices to be interconnected over Wi-Fi. At the same  me, to provide more flexible power 

supply op ons, the ESP32-Ethernet-Kit also supports power over Ethernet (PoE).

What You Need

ESP32-Ethernet-Kit V1.0 board

USB 2.0 A to Micro B Cable

Computer running Windows, Linux, or macOS

You can skip the introduc on sec ons and go directly to Sec on 

Start Applica on Development

.

Overview

ESP32-Ethernet-Kit is an ESP32-based development board produced by 

Espressif

.

It consists of two development boards, the Ethernet board A and the PoE board B, The 

Ethernet

board (A)

 contains Bluetooth / Wi-Fi dual-mode ESP32-WROVER-B module and IP101GRI, a

Single Port 10/100 Fast Ethernet Transceiver (PHY). The 

PoE board (B)

 provides power over

Ethernet func onality. The A board can work independently, without the board B installed.

Содержание ESP32-Ethernet-Kit











Отзывы: