background image

13

13

En

gl

is

h

Notes about the protection circuits

This unit has an output short circuit protection circuit, an overheating 
protection circuit and a direct current protection circuit built-in.

A protection circuit is active when the power indicator blinks blue or 
alternately blue and purple.

 

o

If the power indicator blinks blue, a short might have occurred 
with the +/− speaker cables. In this case, turn the power off and 
check the speaker cable connections.

 

o

If the power indicator blinks alternately blue and purple, the 
internal temperature is high. Turn the unit off and wait a while for 
the temperature to decrease. You can also change the installation 
conditions to improve ventilation.

 

o

If the power indicator blinks alternately blue and purple for 30 
seconds, the unit will automatically turn itself off. After this, the 
POWER button will be disabled for as long as the internal tem-
perature remains high.

If the indicator continues to blink even after likely causes have been 
eliminated, contact the store where you purchased the unit.

Maintenance

Use a soft dry cloth to wipe the surface of the unit clean.
For stubborn smudges, use a damp cloth that has been thoroughly 
wrung out to remove excess moisture.

 

V

For safety, disconnect the power plug from the outlet 
before wiping the unit.

 

o

Never spray liquid directly on this unit.

 

o

Do not use chemically-treated wipes, thinner or similar substances 
because they could damage the surface of the unit.

 

o

Avoid allowing rubber or plastic materials to touch the unit for 
long periods of time, because they could damage the cabinet.

Содержание Grandioso M1













































Отзывы: