background image

Usage instructions

LED Solarlight “Sunnylight”

These instructions relate ONLY to this product and contain important 

information for using the product for the first time. Please keep these 

instructions for later reference and should always accompany the 

product in the event of transference to a new user.

1. Introduction

Dear Costumer, 

Thank you for purchasing the solar light. 

With this solar light you purchased a product manufactured according to 

the current state of technology. 

This product fulfils all requirements of the valid European 

and national regulations. The conformity was proved. The 

relevant declarations and documentation are deposited 

with the manufacturer. 

To maintain this state and guarantee a safe operation, you as the user will 

have to follow this operating manual!

2. Safety Instructions

   

- In case of damages caused by not following this 

  

operating manual, the warranty rights will expire! 

 

We exclude liability for any consequential damages!

 

- We exclude liability for property or personal 

 

damages caused by  inappropriate handling or not 

 

following the safety instructions. 

 

 

- In these cases any guarantee rights will expire.

Due to safety and admission reasons (CE) it is not allowed to arbitrarily 

reconstruct and/or change the solar light. 

Therefore, please keep to the operating manual. 

The accident prevention rules of the association of the industrial trade 

cooperative association for electric plants and working material are to be 

considered in industrial environments

3. Usage in Accordance with Requirements 

The solar light is constructed for the outdoor usage and operation. The 

integrated accumulators are charged by the solar cell in the upper part of 

the light.  At darkness, the light is automatically switched on and is swit-

ched out at sunrise. As light source, 1 very strong „Nichia“ light emitting 

diode (LED) are installed. These LED guarantee a strong luminosity with 

only low power consumption. 

-- However, please note that the duration of illumination may decrea-

se due to a lack of sunshine as well as in the winter months--  

In case of longer periods without sunshine (insolation) the accumulator is 

charged only insufficiently and is thus not able to guarantee a permanent 

readiness for operation. However, this does not indicate that the solar light 

is defect. Please wait for the next sunny days and the light will again be 

working accordingly

4. Initiation

1. Please carefully take all parts out of the package. 

2. Please carefully connect the earth rod with the bar and insert it into the 

ground. 

 Note: Please do not use force. 

3. Hold the upper part and screw off the lower part of the lamp head and 

take apart the parts. Adjust the switch below the lamp shade to the posi-

tion “ON” and carefully insert the upper part of the lamp onto the receiver 

module on the bar.  

  The solar light is now activated. 

In case of wall installation: Unscrew the nuts at the wall carrier and hori-

zontally fix the subbase to the wall with the enclosed screws. Then screw 

on the carrier and reposition the lamp on top.

Note: In order to avoid scratching the wall carrier, do not use sharp-edged 

tools when tightening the nuts.   

Note: The duration of illumination is strongly dependent on the intensity 

and duration of sunshine during the day. During the winter months the 

duration of illumination will generally be shorter. If the lamp should not 

irradiate on the first evening, please wait for a sunny day.

5. Exchange of Accumulators

1. Hold the upper part and screw off the lower part of the lamp head and 

take apart the parts.  

2. Unscrew the reflector clockwise and remove it. 

3. Take the used accumulators out of the battery compartment and insert 

two new accumulators, according to polarity, into the battery compart-

ment. It is recommended to charge the new accumulators in a battery 

charger before inserting them. 

4. Re-assemble the lamp in reverse order. 

Note: Used batteries or accumulators must be disposed of in a non-pollu-

ting way and do not belong into the domestic waste. Your dealer is legally 

obliged to take back and recycle old accumulators. 

6. Malfunctions

-Lamp is not automatically switched on at darkness

- An outside light source (e.g. streetlight) simulates daylight and prevents the lamp 

from switching on. Place the lamp at a darker location. 

- Lamp is not switched on at darkness or only for a short period of time.

- Is the lamp connected?

- Accumulator weak or defective. Exchange of the accumulators.

7. Technical Data

Solar module: 

crystalline silicon 0,4 Wp

Illuminant: 

„Nichia“ light emitting diode (LED) 

Luminous color:  

2800 K (warm white)

Luminosity:  

20 lm

Protection class:  

IP 44

Protection class:  

III

Battery: 

2 x NiMh 1.2 V/900 mAh (Micro, AAA)

Duration of illumination: 

max. 12 hours with fully charged battery pack

Operating temperature range:  

-20°C to + 40°C 

!

GB

Battery take-back

-   Batteries must not be discarded into domestic waste.

-   The consumer is legally required to return batteries after 

use, e.g. to public collecting centers or to battery distribu-

tors. 

-   Contaminant-containing batteries are labeled with the sign 

“crossed-out trashcan“ and one of the chemical symbols. 

Used batteries should be disposed environmentally friendly 

and should not be discarded into domestic waste. Your 

dealer is legally required to take back old batteries.

NiMh

switch

Отзывы: