E200-95-01
I56-3648-020
Schneider Electric Fire and Security Oy, Sokerilinnantie 11 C, 02600 Espoo, Finland
Pittway Tecnologica S.r.l
Via Caboto 19/3
34147 Trieste, Italy
0832
10
EM210E-CZR
DOP-IOD039
EN54-17: 2005
EN54-18: 2005
-20°C
60°C
M200E-SMB
145 g
110 g
A
B
C
x10
x1
-
+
(-)
(+)
1
2
3
4
5
6
7
8
9
10
11
12
0
1
2
3
4
5
6 7
8 9 10
11
12
13
14
15
0
1
2
3
4
5
6 7
8 9
-
+
+
(-)
(+)
I 56- 3648- 020
This manual is intended as a quick reference installation guide. Please refer to the
control panel manufacturers installation manual for detailed system information.
The EM200 series of modules are a family of microprocessor controlled interface
devices permitting the monitoring and/or control of auxiliary devices.The EM210E-
CZR is used to link a zone of conventional devices to an intelligent system controlled
by an addressable panel. The CZR has a resistor built in, making it especially suitable
for connection to a conventional zone that operates in a hazardous area requiring
intrinsically safe equipment.
The module must only be connected to control panels using compatible proprietary
addressable communication protocols for monitoring and control. The module is
compatible with System Sensor intrinsically safe sensors mounted in the B401 base,
for use with these barriers:
MTL models 4561 and 5561.
P Fuchs models KFDO-CS-Ex1.51P and KFDO-CS-Ex2.51P.
NOTE:
When an intrinsically safe system is used on the loop, a short on the sensor
side of the barrier will result in an alarm. Only a short on the module side of the safety
barrier will generate a fault signal.
A single tri-colour LED indicates the status of the module. In normal conditions, the
LED can be set by command from the control panel to blink green when the module
is polled. In the case of a fire alarm on the conventional zone, the LED is switched
on constant red by panel command. If a fault is detected on the conventional zone or
the zone supply voltage drops below 12V, or a fault with the external power supply is
signalled, the LED will blink yellow if enabled on the control panel. When a short circuit
is detected on the loop to either side of the module, the LED is switched to show a
constant yellow light.
SPECIFICATIONS
Intelligent Loop
Operating Voltage Range with Isolator: 15 to 28VDC (Min 17.5VDC for LED operation)
Op. Volt. Range (Isolator Disabled): 15 to 30VDC (Min 17.5VDC for LED operation)
18 to 32VDC if conventional zone is loop powered
Max. Standby Current (µA @24 V and 25
o
C) External Supply Conventional Zone:
No Communication:
288
Communication LED blink enabled - 5 secs:
500
Read 16 sec. LED blink 8 sec:
388
Max. Standby Current (mA @24 V and 25
o
C) Conventional Zone connected to
resistive EOL only (no detectors), Loop Powered Conventional Zone:
No Communication:
6.5
Communication LED blink enabled - 5 secs:
6.7
Read 16 sec. LED blink 8 sec:
6.6
LED Current (Red):
2.2mA
LED Current (Yellow):
8.8mA
Maximum rated continuous current with the
isolator
closed (I
c
max): 1A
Maximum rated isolator switching current (under short circuit) (I
s
max): 1A
Maximum leakage current (I
L
max) with the isolator open (isolated state): 15mA
Maximum series impedance with the isolator closed (Z
c
max): 170 m ohm at 15Vdc
Conventional Zone
External Supply Voltage:
12 to 28.5 VDC
18 to 28.5 VDC if conventional zone is loop powered
Maximum Standby Load Current: 2.8 mA for detectors at 18 VDC
3.8 mA for detectors at 24 VDC
Maximum Zone Load:
60mA (Limited internally)
Maximum Conventional Line Resistance: 50 Ohms
End of Line Resistor:
3.9 K Ohms, 5% (Supplied)
General
Humidity:
5% to 95% relative humidity (non-condensing)
Ingress protection:
IP50 (Mounted in M200E-SMB)
Maximum Wire Gauge:
2.5mm²
INSTALLATION
EM200 series modules can be mounted in several ways (See
Figure 1
):
1:1
An M200E-SMB custom low profile surface-mounting box. The SMB Base is
affixed to mounting surface, and then the module and cover are screwed onto
the base using the two screws supplied. Box dimensions: 132mm(H) x 137mm(W)
x 40mm(D)
1:2
An M200E-DIN Adaptor allows mounting onto standard 35mm x 7.5mm "Top Hat"
DIN rail inside a control panel or other suitable enclosure. Push module into adaptor
bracket until it clips into place. Locate top clip over DIN rail and rotate bottom down
to clip into place. To remove, lift up, then rotate top away from the rail.
1:3
An M200E-PMB Panel Mount Bracket allows the module to be mounted directly
into a panel or other suitable enclosure. Adaptor bracket is mounted directly into
panel using 2 x M4 Pan head screws. Module is pushed into adaptor until it clips
into place.
Wiring to all series EM200 modules is via plug in type terminals capable of supporting
conductors up to 2.5mm²
CAUTION
Disconnect loop power before installing modules or sensors.
The module address is selected by means of rotary decade address switches (see
Figure 3
). A screwdriver should be used to rotate the wheels to select the desired
address, either from the front or the top of the module.
Fig./Abb. 1
1:1 M200E-SMB
1:2 M200E-DIN
1:3 M200E-PMB
EM210E-CZR
INSTALLATION INSTRUCTIONS - EM210E-CZR
CONVENTIONAL ZONE INTERFACE MODULE
EN
Fig./Abb. 3
a
b
c
d
e
f
g
EM210E-CZR
A
B
C
X
1
0
X
1
6
6
23 mm
Fig./Abb. 2
A
B
C
x10
x1
A B
1
0
0
1
2
3
4
5
6 7
8 9 10
11
12
13
14
15
0
1
2
3
4
5
6 7
8 9
1
2
3
4
5
6
7
8
9
10
11
12
94 mm
83 mm
93
mm
h
i
j
k