esera automation 1-Wire Controller 2 Скачать руководство пользователя | Manualshive

Страница: 36 / 77

background image

All rights reserved. Reproduction as well as electronic duplication of this guide, complete or in part, requires the written consent of ESERA-
Automation or E-Service GmbH. Errors and technical modification subject to change.

©

ESERA-Automation, E-Service GmbH 2019

www.esera.de

Programming Manual Controller-Gateway-Station V1.0 R1.1

Page 36 of 77

9.2.

DATA PRINT ON/OFF

Setting of the operating mode for data output of the sensor data
Selectable states: ON = 1 / OFF = 0
OFF = 0 => Data output in one line with one CR, ON = 1 => Continuous output in one line with separator "|".
Factory setting: ON = 1

Command

: SET,SYS,DATAPRINT,0 or 1

9.3.

DATA TIME 0, 10 - 240

Setting of the cycle time for sending 1-Wire / OWD data
Selectable range: 0; 10 - 240
0 = Data only on request, cycle time = 10 - 240 seconds
Factory setting: 10

Command

: SET,SYS,DATATIME,0 or 10 - 240

9.4.

OWB POLLTIME 1 - 240 (data output, available starting with firmware V1.15_51)

Here you can set the poll time for all 1-Wire devices. The time (in seconds) defines, how often the 1-Wire devices
are queried.
Selectable range: Poll time (cycle time) = 1 - 240 seconds.
Note: A poll time faster than 2 seconds should only be selected for a small number of max. 5 or 6 1-Wire devices.
Note: The DATA TIME cannot be selected shorter than the OWB POLLTIME.
(DATA TIME>= POLLTIME).
Factory setting: Poll time is 2 seconds

Command

: SET,SYS,POLLTIME,1 - 240

9.5.

OWB SEARCH ON/OFF

Different methods of searching for OWDs and sorting them into the OWD list can be selected.
Selectable states: ON = 1 or 2, OFF = 0
Details to the two search functions can be found in the programming manual under the tab "DOKU".
0=no search, 1=complete cyclic search (sequence of blocks may change)
2=adaptive cyclic search for new blocks. New blocks are written to the first free space in the OWD list.
Factory setting: ON = 2
Note: With "OWB SEARCH 1" the OWD numbers may be re-sorted.

Command

: SET,OWB,SEARCHTIME,0 - 2

9.6.

OWB SEARCH TIME 10 - 240

Setting of the cycle time for the search function
Selectable range: 10 - 240
Factory setting: 10 seconds,

Command

: SET,OWB,SEARCHTIME,10 - 240

«
...
34
35
36
37
38
...
»

Содержание 1-Wire Controller 2














































































Отзывы:

Нет отзывов

Похожие инструкции для 1-Wire Controller 2

Бренд: Ableconn Страницы: 15

Бренд: fafnir Страницы: 16

Бренд: IFM Electronic Страницы: 6

Бренд: 3idee Страницы: 7

Growing Together

Бренд: Stokke Страницы: 13

Бренд: U.S. Boiler Company Страницы: 20

Бренд: National Instruments Страницы: 27

Бренд: Kramer Страницы: 3

Бренд: ZyXEL Communications Страницы: 6

Бренд: NCR Страницы: 10

Бренд: Thrane&Thrane Страницы: 2

Stylus COLOR 3000

Бренд: Epson Страницы: 1

JS18 Professional

Бренд: Weego Страницы: 16

Бренд: LEGRAND Страницы: 2

Бренд: Belkin Страницы: 2

Бренд: Belkin Страницы: 32

Бренд: Belkin Страницы: 42

Бренд: Belkin Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды