ESD ECS-FPGA Скачать руководство пользователя страница 23

Страница: 23 / 27

Connector Assignments

7. Connector Assignments

7.1 EtherCAT

Both EtherCAT interfaces have the same pin-assignment, each for the corresponding EtherCAT
port.

Device connector:

RJ45 socket, 8-pin

Ethernet 100BASE-TX, assigned according to IEEE 802.3-2008,
Table 25-3 “UTP MDI Contact Assignment”

Pin Position:

Pin Assignment:

Pin

Signal

Meaning

TxD+

Transmit Data +

TxD-

Transmit Data -

RxD+

Receive Data +

RxD-

Receive Data -

Shield

The pins 4, 5, 7 and 8 are connected to termination.

Signal Description:

TxD+/-,
RxD+/- ...

data lines of EtherCAT port

- ...

reserved for future applications, do not connect!

Shield...

case shield, connected with the front panel of the ECS-XMC/FPGA.

Note:

Permissible cable types: Cables of category CAT5 or higher have to be used to grant
the function in networks with up to 100 Mbits/s.
esd grants the EC conformity of the product if the wiring is carried out with shielded
twisted pair cables.

ECS-XMC/FPGA

Hardware Manual • Doc. No.: E.1102.21 / Rev. 1.3

Page 23 of 27

1 2 3 4 5 6 7 8

Содержание ECS-FPGA




























Результаты поиска

Содержание ECS-FPGA

Отзывы:

Бренды по названию

Популярные бренды

ESD ECS-FPGA, Руководство по оборудованию

Результаты поиска

Содержание ECS-FPGA

Отзывы:

Бренды по названию

Популярные бренды