ES&S DS850 Скачать руководство пользователя | Manualshive

Страница: 16 / 199

background image

Chapter 1: DS850 Overview

10

EVS5200_DOC_SOP_DS850

Software Version 2.10

Published: February 26, 2014

Raising and Lowering the DS850’s Cart Extension

To use the DS850 cart extension, lift up on the
extension until it is level and push up on the
brackets on both sides (as shown in the picture
on the right) until they lock into place.

To lower the extension, simultaneously press
the release button on the inside of the bracket
and press down on the hinge of the bracket.
Repeat this process with the other bracket and
carefully lower the extension. The extension
must not be allowed to drop as to prevent
damage to the extension and the cart.

Uninterruptible Power Supply (UPS)

You must use an Uninterruptible Power Supply (UPS) with the DS850. The UPS will
provide continuous power to the machine and to prevent the DS850 and the attached
printers from being damaged in case of a power surge. .

Installing New Firmware

A certified ES&S Technician will usually install new firmware on the DS850. If you have
been instructed to install the new firmware an ES&S Support Representative will assist
you in the process.

Note:

The DS850 was certified using an external UPS to comply with electrical test

requirements in the VVSG. The DS850 must be operated with an external UPS to be in a
certified configuration.

Reference:

See

Chapter 5: Pre-Election Day Tasks

for information on installing the UPS,

attaching the DS850 and printers to the UPS, turning on the UPS, and checking that the UPS
is communicating with the DS850.

Warning:

Contact an ES&S Technician for instructions to return your DS850 to an earlier

firmware version. Do not use an earlier firmware update Compact Flash card to revert a
DS850 firmware version back to an earlier version.

Note:

The Compact Flash card must be a minimum of 1 GB.

«
...
14
15
16
17
18
...
»

Содержание DS850








































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DS850

Power Xpert C445

Бренд: Eaton Страницы: 2

Бренд: janitza Страницы: 30

Бренд: Park Tool Страницы: 4

Бренд: Zehnder Rittling Страницы: 32

CB Ohio Special 100 HP

Бренд: CleaverBrooks Страницы: 200

Бренд: Sumitomo Drive Technologies Страницы: 36

Бренд: KTR Страницы: 13

Бренд: Graco Страницы: 2

Бренд: Vecow Страницы: 168

Бренд: GBC Страницы: 59

Бренд: Unitary products group Страницы: 12

Бренд: Enerpac Страницы: 32

Moeller MFD-CP4-CO

Бренд: Eaton Страницы: 41

paintTROTTER REFINISH

Бренд: Lagos Страницы: 56

Бренд: IBASE Technology Страницы: 73

GQM22M5C2H680JB01 Series

Бренд: Murata Страницы: 25

Бренд: Bosch Страницы: 28

Бренд: Bosch Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды