ESAB CIGWELD Transmig 255i Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 96

ESAB CIGWELD Transmig 255i Скачать руководство пользователя страница 35

OPERATING MANUAL

Transmig 220i

Transmig 255i

Transmig 255i

Manual 0-5550

5-1

MIG (GMAW) WELDING

SECTION 5:

MIG (GMAW) WELDING

5.01 Shielding Gas Regulator/Flowmeter Operating Instructions

!

WARNING

This equipment is designed for use with welding grade (Inert) shielding gases only.

Shielding Gas Regulator/Flowmeter Safety

This regulator/flowmeter is designed to reduce and control high pressure gas from a cylinder or pipeline to
the working pressure required for the equipment using it.

If the equipment is improperly used, hazardous conditions are created that may cause accidents. It is the users
responsibility to prevent such conditions. Before handing or using the equipment, understand and comply at
all times with the safe practices prescribed in this instruction.

SPECIFIC PROCEDURES for the use of regulators/flowmeters are listed below.

1. NEVER subject the regulator/flowmeter to inlet pressure greater than its rated inlet pressure.

2. NEVER pressurize a regulator/flowmeter that has loose or damaged parts or is in a questionable

condition. NEVER loosen a connection or attempt to remove any part of a regulator/flowmeter until
the gas pressure has been relieved. Under pressure, gas can dangerously propel a loose part.

3. DO NOT remove the regulator/flowmeter from a cylinder without first closing the cylinder valve and

releasing gas in the regulator/flowmeter high and low pressure chambers.

4. DO NOT use the regulator/flowmeter as a control valve. When downstream equipment is not in use for

extended periods of time, shut off the gas at the cylinder valve and release the gas from the equipment.

5. OPEN the cylinder valve SLOWLY. Close after use.

«
...
33
34
35
36
37
...
»

Содержание CIGWELD Transmig 255i

































































































Отзывы:

Нет отзывов