Erskine Attachments 66 V4 страница 10 Скачать руководство пользователя | Manualshive

Страница: 10 / 28

background image

10

OPERATING INSTRUCTIONS

3. With the engine at low RPM, lower the loader

lift arms fully and position the attachment flat on
the ground.

4. Engage the auxiliary hydraulics, increase the

engine speed to full RPM, and drive the loader
forward into the work area.

NOTE:

Raising the front of the attachment may

help while driving forward into thick brush and
when turning. Tilt attachment down to start
cutting.

NOTE:

The mower can be operated with the

loader arms in float mode, if so desired.

Optional Wheel Kit

The optional wheel kit can be bolted to the front of
the mower to reduce scalping when turning on
grass. It is not recommended to have the wheels
installed when mowing in heavily wooded areas as
they can become damaged from hitting large trees.

«
...
8
9
10
11
12
...
»

Содержание 66 V4





























Отзывы:

Нет отзывов

Похожие инструкции для 66 V4

Бренд: Tanaka Страницы: 8

Бренд: Etesia Страницы: 24

Бренд: Parklander Страницы: 42

Бренд: Gardena Страницы: 13

Hayterette 005E

Бренд: Hayter Страницы: 36

SDNSL 108 Hydro

Бренд: Stiga Страницы: 38

Бренд: Honda Страницы: 24

Бренд: Qualcast Страницы: 16

Бренд: Simplicity Страницы: 16

Бренд: Jacobsen Страницы: 50

A12612A Stockman PRO

Бренд: COX Страницы: 48

EXPERIENCE Estate 798e

Бренд: Stiga Страницы: 1052

LX466 13AT61RH044

Бренд: Toro Страницы: 36

Бренд: Cub Cadet Страницы: 9

Бренд: GGP Sweden Страницы: 52

Бренд: GGP ITALY Страницы: 58

Бренд: Daken Страницы: 9

Бренд: EMAK Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды