background image

4

3BA00253-01 

 2021-05-17 

 Rev. 1 

Ersa i-CON 1V & i-CON 1VC

2. 

Start-up

2.1 

Unpacking the soldering station

Please use your delivery note to check the contents of the packaging for completeness. If 
the components listed therein are damaged or incomplete, please contact your supplier.

2.2 

Mounting the soldering station

 

Mount the soldering station in a dry place on a heat-resistant, flat 

surface

 

Place the holder next to the soldering station on the heat-resistant 

surface.

 

Place the dry cleaner in the holder.

 

Before switch-on, check whether the line voltage matches the value 

specified on the nameplate.

 

Make sure the soldering tip is properly seated.

 

To switch off the soldering station, use the on/off switch.

 

 Connect the soldering tool to the station. In doing 
so, align the anti-twist protection of the plug with the 
mark on the bottom socket. 

 

 Insert the plug into the socket and then lock it clock-
wise with the coupling nut. 

 

Place the soldering tool in the holder

 

Connect the supply cable to the soldering station and 

the power point.

 

If the soldering station is equipped with an additional 

interface on the back of the device, connect it there: 

Ersa solder fume extractor and preheating plate 

 

IRHP 100.

 

Place the soldering station and the relevant holder on a heat-
resistant, conductive ESD work surface with a connected earthing 
plug, as described under ESD-hazardous components. Tipping over 
must be ruled out for any equipment at all events. 
Place boards on an ESD work surface only.

Start-up

Содержание i-CON 1V















Отзывы: