background image

3

3BA00253-01 

 2021-05-17 

 Rev. 1 

Ersa i-CON 1V & i-CON 1VC

1. 

Introduction

This quick guide is intended to provide you with quick reference options when working 

with i-CON 1V / 1VC. 

The i-CON 1VC soldering station model is optionally available with 

a serial PC interface. Control signals for activating the Easy Arm 1 and Easy Arm 2 solder 
fume extractors or the IRHP 100A heating plate are also available at this interface. A 

ready signal and a standby signal can be output.

This quick guide does not replace the operating instructions!

You should, therefore, read the instruction manual before operating the 
equipment for the first time. Pay special attention to the safety alerts 
listed there!

 

Keep all instructions in a place that can be accessed by all users at any 
time!

The accompanying information paper “Safety Alerts” is also part of the 
safety instructions to be adhered to.

Info ESD-hazardous components!

Electronic components can be damaged by electrostatic discharge. Abide 

by the warnings on the packaging, or contact the manufacturer or suppli-
er. To protect these components, an ESD-safe workplace (ESD = electro-

static discharge) will be suitable.

1.1 

Explanation of symbols

The following symbols are used in this quick guide:

This symbol is used to highlight text passages that contain explanations, 
info or tips.

 

This mark highlights

• 

activities to be carried out, or

• 

instructions to be strictly abided by.

Introduction

Содержание i-CON 1V















Отзывы: