ermaf GP 40 ACU Скачать руководство пользователя

Страница: 9 / 24

GB-9

RUS

G+ K gas*

Gas type

Wobbe index [MJ/m

] [mbar]

min.

max.

G+ K gas

43.46

45.3

13.5

* see page 23 (The Netherlands)

▷

Converting the heating value/Wobbe index to
kWh/m

kWh/m

= Heating value/Wobbe index [MJ/m

]

3.6

▷

Always use a pressure gauge to adjust the burner

gas pressure. The white scale on the adjusting
screw may differ.

0

If all heaters are heating at the same time, com-

pare the required gas pressure on the burner
with the gas pressure p

read off the pressure

gauge, adjust it and monitor the pressure gauge.

+ -

▷

The flame must be blue and must remain inside

the device.

▷

Check and adjust the burner pressure p

and

flame signal on all devices so that the system
operates correctly.



Remove the pressure gauge from the test point.

+ -



Close the pressure test point.

+ -

Flame signal

▷

The flame signal can be displayed while the

burner is operating.



Press the RESET button to display the flame

signal.

▷

The flame signal is shown in coded form as a

number from 0 to 9.

This number must be multiplied by a factor of 2.

The result of this multiplication is the level of the

flame signal in µA. Example: the number 3 cor-

responds to a flame signal of 6 – 8 µA.

Display

Flame

current [µA]

Display

Flame

current [µA]

0 – 2

10 – 12

2 – 4

12 – 14

4 – 6

14 – 16

6 – 8

16 – 18

8 – 10

18...



Check the flame signal.

▷

The flame signal is displayed for 20 s.



Press the RESET button to exit the flame signal

display.

Содержание GP 40 ACU

























Результаты поиска

Содержание GP 40 ACU

Отзывы:

Похожие инструкции для GP 40 ACU

Бренды по названию

Популярные бренды

ermaf GP 40 ACU, Руководство по эксплуатации

Результаты поиска

Содержание GP 40 ACU

Отзывы:

Похожие инструкции для GP 40 ACU

Бренды по названию

Популярные бренды