ermaf GP 40 ACU Скачать руководство пользователя страница 22

Страница: 22 / 24

GB-22

RUS

Spare parts

▷

When ordering spare parts, please quote the order number along with the designation and item no. of
the spare part as well as the heater serial number.

▷

When ordering spare parts which are not listed here below, please quote the edition of these operating

instructions and the heater serial number.

▷

Use genuine spare parts only to ensure the replacement complies with the requirements stipulated by
the manufacturer.

1a, 1b

2 3

15, 16

22, 23

11, 12

7, 8

Item Order No.

Designation

1a
1b

N50260351
N50260361

Fan motor, 50 Hz, GP 40
Fan motor, 60 Hz, GP 40

N70300084 Flexible connection pipe for GP 40/70

N70300100 Vane switch, complete, for GP 40 ACU

N70300053
N70300054

Natural gas nozzle for GP 40 ACU
Propane nozzle for GP 40 ACU

N70300058 Burner baffle plate for GP 40/GP 70

N70300064 Flame rod for GP 40/GP 70

N70300108 Ionization cable kit for GP 40/GP 70 ACU

Housing for GP 40 ACU

N70300024 Burner chamber for GP 40 ACU

N70300063 Spark plug for GP 40/GP 70

N70300104 Ignition cable kit for GP 40/GP 70 ACU

N70300095 Safety temperature limiter (STL) for GP 14 – GP 120 ACU

N50260109 Ignition transformer for GP series

N70300005 ACU 121, complete

N70300007 Burner Chip Card (BCC) for GP series

N70300075 Angle flange, outlet, for GP 40 ACU

N70300073 Gas combination control CG 10 for GP 40 ACU

N70300088 Complete cable kit for GP ACU

N70300080 Angle flange, inlet, for GP 40 ACU

N52700002 Safety grille for GP 40/GP 70

N50260399 Fan impeller wheel, 50 Hz

N50260395 Fan impeller wheel, 60 Hz

N50260244 Fan inlet hood for GP 40/GP 70 ACU

N70300147 Cover for maintenance opening, for GP 40/GP 70 ACU

Содержание GP 40 ACU

























Результаты поиска

Содержание GP 40 ACU

Отзывы:

Похожие инструкции для GP 40 ACU

Бренды по названию

Популярные бренды

ermaf GP 40 ACU, Руководство по эксплуатации

Результаты поиска

Содержание GP 40 ACU

Отзывы:

Похожие инструкции для GP 40 ACU

Бренды по названию

Популярные бренды