Ericsson TANDBERG Television iPlex N20001 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 98

Ericsson TANDBERG Television iPlex N20001 Скачать руководство пользователя страница 43

iPlex Installation and Hardware Specification Guide

43

Specifications

Mechanical

Height:

0.509 inches

Width:

2.913 inches

Depth:

5.866 inches

Connectors:

37 Pin Micro-D Connector, BNC

Indicators

RDY

—Ready Green LED

ACT

—Active Green LED

Real-Time

MPEG-4 AVC

Ultracompression

Encoder

The Real-Time MPEG-4 AVC Ultracompression Encoder submodule can receive
both Standard Definition and High Definition uncompressed digital video
through a variety of input interfaces and compress it to MPEG-4 Part 10 (H.264).
The following physical input options are offered:

•

HD card: encoders fitted with this interface can accept HD-SDI and SD-SDI input signals (on
the same physical BNC interface).

•

SD card: encoders fitted with this interface only accept SD signals. The interface options are
Composite, S-Video, and SD-SDI, in the exact same arrangement as the MPEG-2 Encoder
Plus and the H.264 Advanced Encoder.

•

The encoder supports up to six audio stereo pairs, depending on the selected
audio compression scheme. The first two audio pairs can be analog-balanced or
unbalanced signals, connected through the 37-pin micro-D connector. When
using AES signals, the 37-pin micro-D connector allows for up to four stereo
pairs. The remaining channels are only available as embedded audio in the HD-
SDI or SD-SDI interface.

State

RDY

ACT

Power Off or Not Initialized

Off

Off

MPEG Encoder enabled, no video present on selected
input: C2/C or C1/Y/SDI

On

Off

MPEG Encoder enabled, video present on selected
input: C2/C or C1/Y/SDI

On

Flashes

NOTE

HD operation requires a license key.

NOTE

The audio cables used in the MPEG-2 Encoder Plus and in the
Advanced Encoder are compatible with this module.

«
...
41
42
43
44
45
...
»

Содержание TANDBERG Television iPlex N20001



































































































Отзывы:

Нет отзывов