manualshive.com logo in svg

Ericsson TANDBERG Television iPlex N20001, Руководство по установке, Страница: 39 / 98

Поделиться
Скачать
Ericsson TANDBERG Television iPlex N20001 Скачать руководство пользователя страница 39

iPlex Installation and Hardware Specification Guide

 

                                                                                                                                                       39     

Indicators

RDY

—Ready Green LED

ACT

—Active Green LED

ASIOut

Submodule

The ASIOut submodule is distinguished by its label (ASIOUT) and by an orange 
line around the BNC connectors. Looking at the interface view of the card, you 
can see BNC connectors and activity LEDs.

Specifications

Mechanical

Height:

0.509 inches

Width:

2.913 inches

Depth:

5.866 inches

Connectors:

BNC

Indicators

RDY

—Ready Green LED

ACT

—Active Green LED

State

RDY

ACT

Power Off

Off

Off

LED test for approximately 8 seconds, 
following power up and board configu-
ration.

On

On

ASI In Port disabled

Flash-
ing

Off

ASI In Port enabled, no ASI In traffic

On

Off

ASI In Port enabled, ASI In traffic

On

Flash rate proportional 
to MPEG TS packet rate

RDY ACT

RDY ACT

ASI OUT

1A

1B

2A

2B

Содержание TANDBERG Television iPlex N20001



































































































Отзывы:

Нет отзывов