Ericsson iPECS-100 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 464

background image

iPECS-LIK

Feature Description & Operation Manual

Issue 6.1

25

Hardware

2.5.5 Calls-In-Queue Page Alert

Description

The administrator can establish CIQ (Calls-In-Queue) thresholds for each ACD Group so that
an assigned VMIM/VSF announcement plays over a defined Page zone, if the number of calls
in queue equals or exceeds a CIQ threshold. The message, which is recorded by an Attendant,
plays immediately or after a defined delay. The message repeats at assigned intervals until the
number of Calls in Queue falls below the threshold. iPECS allows different treatment and
VMIM/VSF announcements for up to three different Calls-In-Queue thresholds.

Operation

System

When the number of Calls-In-Queue changes, up or down the iPECS;

1. Checks CIQ thresholds,

2. Determines if threshold is reached,

3. Queues announcement for threshold (sets Delay timer),

4. Plays CIQ announcement.

5. Repeats announcement as defined.

System Attendant

To record a CIQ Announcement for an ACD Group;

1. Press the

[PGM]

button.

2. Dial

“06”, the Message Record code.

3. Dial VSF/VMIM sequence number to select a VSF/VMIM.

4. Dial the VMIM/VSF Announcement number (01-70)

5. Dial language selection (1~3), the current announcement is played followed by the

“Press # to record” prompt.

6. Dial

“#”.

7. After the beep-tone, record message.

8. Press the

[SAVE]

button to stop recording and save the message.

To delete a recording

1. Press the

[PGM]

button.

2. Dial

“06”, the Message Record code.

3. Dial VSF/VMIM sequence number to select a VSF/VMIM.

4. Dial the VMIM/VSF Announcement number (01-70)

5. Dial language selection (1~3), the current announcement is played followed by the

“Press # to record” prompt.

6. Press the

[SPEED]

button during playback to erase message.

Conditions

1. Thresholds are assigned as total Calls-In-Queue to activate a Page alert and are

checked from lowest priority (CIQ #1) to highest priority (CIQ #3). Thus, the

«
...
37
38
39
40
41
...
»

Содержание iPECS-100

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для iPECS-100

BladeCenter HS22

Бренд: IBM Страницы: 18

Бренд: Longshine Страницы: 56

SUPERSERVER 6028TP-HTFR

Бренд: Supero Страницы: 141

Бренд: Sun Microsystems Страницы: 138

Бренд: Qeedji Страницы: 58

Бренд: Vxl Страницы: 19

Бренд: Olive Страницы: 19

419452u - Servers System X3250 M2 Xeon...

Бренд: IBM Страницы: 84

Бренд: Kontron Embedded Computers Страницы: 46

Бренд: 2Wire Страницы: 2

Бренд: Samsung Страницы: 58

Бренд: Lightwave Communications Страницы: 97

T19 Hydro Server

Бренд: BITMAIN Страницы: 17

AcquiLite A7810

Бренд: Obvius Страницы: 29

Бренд: Polycom Страницы: 34

Бренд: NuPrime Страницы: 26

Бренд: Camerio Страницы: 178

Бренд: x-odos Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды