Ericsson iPECS-100 Скачать руководство пользователя страница 324 | Manualshive

Страница: 324 / 464

background image

iPECS-LIK

Feature Description & Operation Manual

Issue 6.1

287

4.10 DIRECT INWARD SYSTEM ACCESS (DISA)

Description

Each CO/IP path may be assigned for DISA service, which allows an incoming caller to gain
access to the system resources and/or features. The iPECS will answer the outside call and
provide the user intercom dial tone or route the call based on the VMIM/VSF Auto Attendant
announcement settings where Caller Controlled Routing may be defined. The DISA caller may
then access the desired resource using dial codes.

If an Authorization Code is required for DISA access, when the system answers an incoming
DISA call, DND Warning tone is provided to indicate an Authorization Code must be entered.

Operation

System

Incoming call subject to DISA service

1. Recognize incoming call.

2. Answer call and connect caller to Intercom dial tone or AA announcement.

3. Process call based on received digits/programming.

DISA Caller

To access the system

’s resources from an external party

1. Place call to DISA facility of the system.

2. At receipt of Intercom dial tone/AA announcement, dial as desired. If DND Warning

tone is received, enter an Authorization Code, to receive Intercom dial tone.

Conditions

1. Each CO/IP path is separately assigned for DISA operation during Day, Night

and/or Timed system operation mode. DISA operation is active only when the
system is in the assigned operating mode(s).

2. DISA callers can be routed to a VMIM/VSF Auto Attendant announcement in place

of Intercom dial tone. The announcement can be associated with a CCR Table or
assigned to disconnect after playback

(“#”).

3. A DISA caller can be required to enter an Authorization Code to access the

system

’s external outgoing resources, facilities or features. If required, the caller is

permitted to retry entry of a valid Authorization Code based on the DISA Retry
count. Continued failure results in disconnect.

4. DISA callers are subject to COS dialing restrictions. If Authorization Codes are

required and the code entered matches a Station Authorization Code, the station

’s

COS will apply. Otherwise, the assigned DISA COS will apply. In both cases, the
CO/IP COS for the outgoing path will be active.

5. The system will disconnect an outgoing DISA call if the Unsupervised Conference

timer expires or disconnect supervision is received. A disconnect warning tone is
provided 15 seconds prior to disconnect.

6. If a DISA caller encounters a system All Lines Busy, busy tone is received for 5

seconds before ICM Dial tone is again presented and the DISA caller may try
another call.

«
...
322
323
324
325
326
...
»

Содержание iPECS-100

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для iPECS-100

8835 - Eserver 325 - 1 GB RAM

Бренд: IBM Страницы: 68

Бренд: IBM Страницы: 42

Бренд: ACTi Страницы: 15

Бренд: Pathos Acoustics Страницы: 26

Бренд: Vxl Страницы: 2

Бренд: MSI Страницы: 54

TeraStation TS-RXL/R5

Бренд: Buffalo Страницы: 91

Бренд: Viavi Страницы: 11

Бренд: Planet Страницы: 24

Бренд: Black Box Страницы: 3

Бренд: ASUSTOR Страницы: 11

Rackable C1110-RP6

Бренд: Silicon Graphics Страницы: 58

InfiniteStorage 3104

Бренд: Silicon Graphics Страницы: 64

Бренд: Inspur Страницы: 147

Бренд: Dell EMC Страницы: 108

PowerEdge R7525

Бренд: Dell EMC Страницы: 209

Бренд: Dell EMC Страницы: 60

Applause Media System

Бренд: GILBARCO VEEDER-ROOT Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды