Ericsson iPECS-100 Скачать руководство пользователя страница 270 | Manualshive

Страница: 270 / 464

background image

iPECS-LIK

Feature Description & Operation Manual

Issue 6.1

235

2.79 SYSTEM CALL ROUTING

Description

System can change destination automatically or manually by condition of time , days , CLI,
CPN, CO, Zone and Tenancy Group number about incoming calls. If scenarios are set,
incoming calls are routed to the destination(like as 231 Flex Did destination) by the condition.

Item of Condition Table



Caller ID



Called Num



Days and time(Start Day and End Day, weeks, start time and end time)



Destination (Type and Value)



Scenario Priority



Scenario Active or Not



Scenario Voice Mail box



Scenario COS



Scenario Disa Active or Not



Scenario Tenancy Group number



Scenario Zone



Scenario Start CO and End CO



Scenario Group : this is used for scenario group by attendant

Conditions

1. Scenario Active should be set ON and Day condition chosen a day or everyday for

operation.

2. Even though System is Day/Night/Timed mode, it works by system call routing

scenario. And so, System call routing is highest priority than others.

3. We recommend that Co and Station are same tenancy group and zone.

4. If Start time is 0700 and End time is 1900, it works from AM 07:00 to PM 07:00.

5. The total numbers of table are 16(MFIM1200 : 32) and have 10 scenario

respectively. And so you can set maximum 160(MFIM1200 : 320) scenarios.

6. VMID should be Station number that is virtual or not. Virtual means that Station

number is exist but it has not Hard Phone. VMID is used when Destination Type is
Hunt and Destination is VSF hunt group.

7. If you set Disa Active ON and Destination is VSF 1, CCR will work after announcing

1.

8. If VSF is 0 and Disa Active ON, you can hear Disa dial tone.

9. If you choose ATD STN for the type of Caller ID, it works rerouting to STA, Hunt,

Mail Box, Network call and SPEED instead of ATD for internal attendant call in this
condition.

10. Scenario group is only used as manual setting by attendant.

11. If attendant want to use manual SCR using Scenario group, you should do as

following.

«
...
268
269
270
271
272
...
»

Содержание iPECS-100

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для iPECS-100

Бренд: Atop Страницы: 2

Бренд: IBM Страницы: 140

Flex System x240 Compute Node

Бренд: IBM Страницы: 28

Бренд: Oki Страницы: 2

Virtual Services Platform 7000 Series

Бренд: Avaya Страницы: 103

Бренд: Vxl Страницы: 19

x3105 - System - 4347

Бренд: IBM Страницы: 130

System x3650 Type 7979

Бренд: IBM Страницы: 194

Бренд: Asus Страницы: 186

ProLiant BL460c Gen8

Бренд: HP Страницы: 84

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 25

Бренд: Promise Technology Страницы: 324

DeviceMaster PRO

Бренд: Comtrol Страницы: 174

m330 media server

Бренд: Wadia Страницы: 24

SUPERSERVER 6026TT-IBQF

Бренд: Supermicro Страницы: 100

SuperServer 510P-WT

Бренд: Supermicro Страницы: 113

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды