Ericsson iPECS-100 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 464

background image

iPECS-LIK

Feature Description & Operation Manual

Issue 6.1

6

2.2 ALARM SIGNAL/DOOR BELL

Description

The system can be configured to recognize the status of an external contact (normally open or
closed). The system will signal assigned iPECS Phones when the contact activates. This
capability is commonly employed to provide remote Alarm or Door Bell signals to the user.

Assigned stations receive the Alarm Signal, either a single tone burst repeated at 1-minute
intervals or a continuous tone. The Alarm Signal may be terminated at the user

’s phone by

dialing the Alarm Stop code or, if assigned, pressing the

{ALARM STOP}

button. To rearm the

Alarm function, the alarm condition must be cleared and the Alarm signal terminated.

When used as a Door Bell, assigned iPECS Phones receive a single tone burst each time the
external contact is activated and no reset is required.

Operation

System

At detection of contact operation, the Alarm/Door Bell signal is sent to assigned stations.

iPECS Phone

To assign a Flex button as an

{ALARM STOP}

button to terminate the Alarm Signal:

[PGM]

+

{FLEX}

+

“565” +

[SAVE]

To terminate an Alarm Signal while idle:

1. Dial the Flex Numbering Plan code 565, confirmation tone is received and the Alarm

Signal is terminated. If the alarm condition is cleared, the system will automatically
rearm the alarm monitoring.

Or,

2. Press the

{ALARM STOP}

button.

Conditions

1. The Alarm contacts must be

“dry”, no voltage or current source connected.

2. Only an iPECS Phone may be assigned to receive Alarm/Door Bell signals.

3. An iPECS Phone with LCD assigned to receive Alarm/Door Bell signals will show

“ALARM” or “DOOR BELL” as appropriate.

Programming

SYSTEM

1 Alarm Enable (PGM 163-Btn 1)

2 Alarm Contact Type (PGM 163-Btn 2)

3 Alarm/Doorbell Mode (PGM 163-Btn 3)

4 Alarm Signal Mode (PGM 163-Btn 4)

STATION

1 Alarm/Door Bell Attribute (PGM 113-Btn 8)

Related Features



Door Open

«
...
18
19
20
21
22
...
»

Содержание iPECS-100

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для iPECS-100

Бренд: F5 Страницы: 72

Бренд: SEH Страницы: 20

847620U - Netfinity 3000 - 20U

Бренд: IBM Страницы: 270

A+ AS-2124US-TNRP

Бренд: Supermicro Страницы: 130

SuperServer 6019P-WT

Бренд: Supermicro Страницы: 133

Бренд: Airlink101 Страницы: 36

Бренд: EDSLab Страницы: 24

Бренд: Samsung Страницы: 58

DOMINION KSX II

Бренд: Raritan Страницы: 362

Бренд: Sonnet Страницы: 16

Бренд: PRG Страницы: 136

TourMaster MLA2504

Бренд: Coachsound Страницы: 22

Бренд: Chip PC Страницы: 4

Бренд: Black Box Страницы: 66

InfiniteStorage 3000

Бренд: Silicon Graphics Страницы: 50

Бренд: AirLive Страницы: 89

Бренд: Antrica Страницы: 57

Бренд: CTC Union Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды