Ericsson EXN401 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 180

Ericsson EXN401 Скачать руководство пользователя страница 26

Command Line Interface

2.5

Privileged EXEC Mode

2.5.1 atm-format

Description

This command is used to configure the ATM format between

Network Network Interface (NNI) and User Network Interface (UNI). Once
you change the settings, no further configuration is allowed and you will be
asked to save your configuration and reboot the system. Note that this
parameter is part of the system startup configuration and is not reset by the

clearconf

command without the

all

option.

Syntax

atm-format [nni|uni]

nni

Selects the NNI format.

uni

Selects the UNI format.

If no parmeter is specified, the command displays the current ATM format.

Default

NNI

Show

show atm-format

Modes

Privileged EXEC

Example

To configure the ATM format to UNI:

EXN400# atm-format uni

2.5.2 buffers

Description

This command is used to configure the system buffer pool.

User can specify the buffer size and the system automatically computes the
number.

The buffers are used to receive and transmit data on any communicating
channel (ATM PVC, Ethernet interface). Each time a new channel is
defined, some buffers are reserved. The number of buffers reserved for
each channel depends on the size of the transmit queue for this channel.
The transmit queue size can be configured by using the

tx-queue-size

command.

The buffer size limits the Maximum Transmit Unit (MTU) size. One buffer
must be able to contain the largest MTU and an extra 120-bytes overhead.

12

1553-LZY 214 2655 C 2004-11-24

«
...
24
25
26
27
28
...
»

Содержание EXN401





















































































































































































Отзывы:

Нет отзывов