Ercogener 4408100066 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 51

Ercogener 4408100066 Скачать руководство пользователя страница 39

EG_GenPro425e_1103_UG_001_UK.docx

Page 39 / 51

Descriptions and non-contractual illustrations in this document are given as an indication only.

ercogener reserves the right to make any modifications.

Dct_427_02

5 Use of the modem

5.1 Specific recommendations for the use of the modem in vehicles

The power supply connector of the modem

GenPro 425e

must NEVER be connected directly

to the battery of the vehicle. The cable must be connected to a protected circuit, power
source PS1 (max 15W). Either by a 1A fuse under 12Vdc or by 0.5A fuse under 24Vdc

5.1.1

Recommended connection on the battery of a truck

All trucks have a circuit breaker outside the cabin. The circuit breaker is used for security reasons:

The circuit breaker is connected to the ground of the truck, usually connected to the fuse box.

Most of truck circuit breakers do not cut the

+

'

PLUS

' of the battery, but cut its

'

GROUND

'

.

Figure 23 : Recommended connection on the battery of a truck

The scheme above shows a recommended power connection where the connection of the modem ground is

not directly connected to the battery, but connected after the circuit breaker (on the ground of the truck or in

the fuse box).

If this scheme is not respected, the modem can be damaged when starting the truck if the
circuit breaker is open. It cannot support important starting currents.

«
...
37
38
39
40
41
...
»

Содержание 4408100066




















































Отзывы:

Нет отзывов