Erco & Gener GenPro 22e Скачать руководство пользователя страница 58

Страница: 58 / 63

EG_GenPro2xe_1003_UG_005_UK

Page 58 / 63

Descriptions and non-contractual illustrations in this document are given as an indication only.

ERCO&GENER reserves the right to make any modifications.

Dct_427_00

8.2.6.2 GSM external antenna

The GSM external antenna is connected to the modem via the SMA/M connector.

The external antenna must have the characteristics described in the table below.

Table: Characteristics of the GSM external antenna

Frequency band

850/900/1800/1900 MHz

Impedance

50 Ohms nominal

DC impedance

0 Ohm

Gain

0 dBi in a minimum direction

VSWR (Rx max TX max)

1.5:1

Polarization Linear

See chapter 10 for the GSM antennas recommended by ERCO & GENER.

8.2.7 Characteristics of the accelerometer

Table: Characteristics of the accelerometer

Dynamic

± 2g or ± 8g driven by software

Interface (internal)

SPI with the ARM

Multiple Interruption

programmable

Up-going filter

programmable

8.3 Environmental characteristics

To ensure a correct functioning of the modem, the limits listed in the table below must be respected.

Table: Environmental characteristics

Operating temperature

-20 °C à +60 °C

Storage temperature

-40 °C à +85 °C

Operating humidity without condensation

HR < 70% @ +55°C

Atmospheric pressure

normal

If the battery option is used, the environmental conditions are different. See table below.

Содержание GenPro 22e
































































Результаты поиска

Содержание GenPro 22e

Отзывы:

Похожие инструкции для GenPro 22e

Бренды по названию

Популярные бренды

Erco & Gener GenPro 22e, Руководство пользователя

Результаты поиска

Содержание GenPro 22e

Отзывы:

Похожие инструкции для GenPro 22e

Бренды по названию

Популярные бренды