Erco & Gener GenPro 22e Скачать руководство пользователя страница 57

Страница: 57 / 63

EG_GenPro2xe_1003_UG_005_UK

Page 57 / 63

Descriptions and non-contractual illustrations in this document are given as an indication only.

ERCO&GENER reserves the right to make any modifications.

Dct_427_00

8.2.5 RESET signal

Cabling Scheme

Table: Conditions of use

Parameters

Condition

Min.

Typ.

Max.

Unit

Input Voltage – Low or float

-0.3

0.8

Vdc

Input Voltage – High

3.3

Vdc

IPU

Internal Pull-Up Resistor

5.38K

Ohms

8.2.6 RF GSM/DCS characteristics

8.2.6.1 RF functioning

The RF functioning complies with the ETSI GSM Standards.

The RF performances for the receiver and the transmitter are described below.

Table: Parameters of the RF receiver and transmitter

Receiver

Sensitivity in 850/900

- 106 dBm, GPRS Coding Scheme 1 (CS1)

Sensitivity in 1800/1900

- 106 dBm, GPRS Coding Scheme 1 (CS1)

Transmitter

Maximum power (Power Class1 - 850/900)
at ambient temperature

33 dBm +/- 2 dB @ antenna connection

Maximum power (Power Class4 - 1800/1900)
at ambient temperature

30 dBm +/- 2 dB @ antenna connection

Содержание GenPro 22e
































































Результаты поиска

Содержание GenPro 22e

Отзывы:

Похожие инструкции для GenPro 22e

Бренды по названию

Популярные бренды

Erco & Gener GenPro 22e, Руководство пользователя

Результаты поиска

Содержание GenPro 22e

Отзывы:

Похожие инструкции для GenPro 22e

Бренды по названию

Популярные бренды