manualshive.com logo in svg

Erco & Gener GenPro 22e, Руководство пользователя, Страница: 25 / 63

Поделиться
Скачать
Erco & Gener GenPro 22e Скачать руководство пользователя страница 25

 

EG_GenPro2xe_1003_UG_005_UK 

Page 25 / 63

 

 

Descriptions and non-contractual illustrations in this document are given as an indication only. 

 

ERCO&GENER reserves the right to make any modifications. 

Dct_427_00 

5.2 Specific recommendations for the use of the modem in vehicles 

 

 

The power supply connector of the modem GenPro 2xe  must 

NOT

 be connected directly to 

the battery of the vehicle. 

 

 

5.2.1 Recommended Connection on the battery of a truck 

All lorries have a Circuit Breaker outside the cabin. The circuit breaker is used for security reasons: for 

example, if a fire breaks out in the electric box of the lorry, the driver can cut off the power source and avoid 

more damage (explosion). 

The circuit breaker is connected to the ground of the lorry, usually connected to the fuse box. 

Most of lorry circuit breakers do not cut off the PLUS of the battery, but cut off the ground. 

 

 

GenPro 2xe 

 

The scheme above shows a recommended power connection where the connection of the modem ground is 

not directly connected to the battery, but connected after the circuit breaker (to the ground of the lorry or in 

the fuse box). 

Содержание GenPro 22e
































































Отзывы:

Нет отзывов