EQUYSIS ULTRA-E-F Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 63

EQUYSIS ULTRA-E-F Скачать руководство пользователя страница 17

14

ULTRA-E-F

PART-3 TRANSMITTER INSTALLATION AND OPERATION

INSTRUCTIONS

Transmitter Installation

After unpacking, it is recommended to save the shipping carton and packing materials in case

the instrument is stored or re-shipped. Inspect the equipment and carton for damage. If there is

evidence of shipping damage, notify the carrier immediately.

The enclosure should be mounted in an area that is convenient for servicing, calibration or for

observation of the LCD reading.

1 Locate the transmitter within the length of transducer cable that was supplied with the

ULTRA-E-F system. If this is not possible, it is recommended that the cable be exchanged for

one that is of proper length. Transducer cables that are up to 990 feet [300 meters] may be

accommodated.

2.

Mount the ULTRA-E-F transmitter in a location that is:

♦

Where little vibration exists.

♦

Protected from falling corrosive fluids.

♦

Within ambient temperature limits -40 to 131°F [-40 to 55°C]

♦

Out of direct sunlight. Direct sunlight may increase transmitter temperature to above the

maximum limit.

3.

Mounting: Refer to

Figure 3.1

for enclosure and mounting dimension details. Ensure that

enough room is available to allow for door swing, maintenance and conduit entrances.

Secure the enclosure to a flat surface with four appropriate fasteners.

Figure 3.1 Mechanical Dimensions

«
...
15
16
17
18
19
...
»

Содержание ULTRA-E-F
































































Отзывы:

Нет отзывов